Sea Tel ST14 Скачать руководство пользователя страница 14

Страница: 14 / 84

Installation

ST14 Ku-Band TVRO

1-8

NOTE: The Radome Base contains weep holes to allow any
water that potentially may enter radome to weep out. Do

not confuse these radome “weeping” holes with the actual

mounting inserts. Exercise caution as to not allow anything,

including the mounting surface, to block these weep holes.
A failure to comply with this may result in the accumulation

of standing water.

Thread the 6mm bolt through a bonded washer (neoprene

side down) and through one of the threaded inserts in the

base of the radome.

Using a 10mm Socket, Install and tighten an M6 Bolt through

the threaded insert to approximately 7.5 to 9 ft-lbs.

Threaded metal insert

Neoprene washer

M6 Bolt

Rotate the antenna in azimuth and repeat for the three

remaining mounting bolts, tightening all four of the required

mounting bolts to approx 7.5 to 9 ft-lbs.

Reference picture showing one of the four mounting bolts
protruding from radome base and through the mounting

feet.

Radome Base Feet

Mounting Bolt

Weep Hole

Azimuth Lockdown Hole

Содержание ST14





















































































Результаты поиска

Содержание ST14

Отзывы:

Похожие инструкции для ST14

Бренды по названию

Популярные бренды

Sea Tel ST14, Руководство по установке и обслуживанию

Результаты поиска

Содержание ST14

Отзывы:

Похожие инструкции для ST14

Бренды по названию

Популярные бренды