Sea Tel ST14 Скачать руководство пользователя страница 12

Страница: 12 / 84

Installation

ST14 Ku-Band TVRO

1-6

1.12.

Install the Antenna Radome

Refer to the Installation Arrangement drawing for mounting dimensions of the radome assembly. Note that the

Antenna Radome installation procedure are identical for all ST14 Series Systems. Before performing this procedure,
verify all of the system contents with the packing list provided with the shipment.

Figure 1 ST14M Antenna

System

Figure 2 ST14D Antenna System

Figure 3 ST14E Antenna System

Open the Radome Installation Hardware Kit, which should
include the following items:

Radome Mounting Pad

6mm Mounting bolts

6mm Flat Washer

6mm Neoprene Flat Washer

6mm Small OD Flat Washer

6mm Nyloc Nut

Using a #2 Phillips Head Screw driver, remove the 3 screws
(270˚ spacing apart from each other) that secure the radome

top to the radome base.
Set the hardware and radome top aside in a safe location

until you are ready to close the radome.

Содержание ST14





















































































Результаты поиска

Содержание ST14

Отзывы:

Похожие инструкции для ST14

Бренды по названию

Популярные бренды

Sea Tel ST14, Руководство по установке и обслуживанию

Результаты поиска

Содержание ST14

Отзывы:

Похожие инструкции для ST14

Бренды по названию

Популярные бренды