background image

Setup for Model ST14M

 

ST14 Ku-Band TVRO 

 

 

3-8 

3.3.11.1.

 

Latitude Ranges: 

The three latitude ranges in the “LAT-THRESH OFFSET TABLE” are defined by setting 

2 

system parameters, 

“Low Lat Lim” and “High Lat Lim”. 

3.3.11.1.1.

 

The LOW LAT LIM parameter defines 

the “Lower” Latitude Limitation Range 

and is entered using any whole degree 

from 0-90.  The LOW LAT LIM 
parameter sets the highest latitude 

position of the lower latitude range. 

Therefore the lower latitude range will 

be any latitude range from 0° to LOW 

LAT LIM parameter. While in this range, 

the system will use the parameter 
entered for LOW LAT OFFSET for calculating the tracking threshold  

Lower Latitude Range 

Example: To define a Lower Latitude Range of 0° to 35°, enter a LOW LAT LIM parameter 

value of 35. 

1.

 

Press the 

NEXT

 key to select this sub-menu parameter for adjustment.   

2.

 

A cursor will appear under the rightmost digit.  Press 

 & 

 arrow keys to 

increment/decrement this digit.   

3.

 

Press the 

NEXT

 key to move the cursor to the next digit to the left.  Press 

 & 

 

arrow keys to increment/decrement this digit.   

4.

 

Press the 

NEXT

 key to move the cursor to the next digit to the left.  Press 

 & 

 

arrow keys to increment/decrement this digit.   

5.

 

Press the

 SAVE

 key to save the desired parameter 

3.3.11.1.2.

 

The “Middle” Latitude Limitation Range 

is defined by the values set for the LOW 

LAT LIM 

Middle Latitude Range 

and

 HIGH LAT LIM 

parameters.  The HIGH LAT LIM 

parameter sets the highest latitude 
position of the Middle latitude range 

while the LOW LAT LIM parameter 

entered sets the lowest latitude 

position of the Middle latitude range.  

Therefore the Middle latitude range will be any latitude position from the LOW LAT LIM 

parameter to the HIGH LAT LIM parameter.  Example: To define a Middle Latitude range of 
35° to 45°, enter a HIGH LAT LIM of 45 

and

3.3.11.1.3.

 

 enter a LOW LAT LIM of 35° While in this range 

the system will use the parameter entered for MID LAT OFFSET for calculating the tracking 

threshold. 

The HIGH LAT LIM parameter defines the 
“Upper” Latitude Limitation Range and is any 

whole degree from1-90.  The HIGH LAT LIM 

parameter sets the lowest latitude position of 

the Upper latitude range.  Therefore the upper 

latitude range will be any latitude range from 

HIGH LAT LIM to 90°.  Example: To define an 
upper Latitude Range of 45° to 90°, enter a HIGH 

LAT LIM of 45.  While in this range the system 

will use the parameter entered for HIGH LAT 

OFFSET for calculating the tracking threshold. 

Upper Latitude Range 

 

Figure 3-1  Lower Latitude Range 

 

Figure 3-2  Middle Latitude Range 

 

Figure 3-3  Upper Latitude Range 

Содержание ST14





















































































Отзывы: