Sea Tel ST14, Руководство по установке и обслуживанию

Страница: 27 / 84

ST14 Ku-Band TVRO Setup for Model ST14 D
2-7
6. If you do not want to edit any other sub-menu parameters, press
SAVE
again to exit the
sub-menu and return to the SAT main menu display. From there you can press the
▼
arrow key to go to next SAT numeric menu choice or to the Factory Settings menu choice.
2.3.6.
Access all of the SAT2 individual parameters via a sub menu. If a second SAVED satellite is not needed,
preset SAT2 to empty/blank so
NEXT
will skip over this selection when you are switching satellites.
SAT2 - Second Satellite Parameters
All of the SAT2 parameters are set exactly the same way that the SAT1 parameters were set, but would be set
to different choices. Refer to the parameter setting information in the SAT1 – First Satellite Parameters
paragraphs to set PRESET, NAME, LON, RHCP freq, BAUD, FEC, and NID for a second satellite that you wish to
use periodically.
2.3.7.
Access all of the SAT3 individual parameters via a sub menu. If a third SAVED satellite is not needed, preset
SAT3 to empty/blank so
NEXT will skip over this selection when you are switching satellites.
SAT3 - Third Satellite Parameters
All of the SAT3 parameters are set exactly the same way that the SAT1 parameters were set, but would be set
to different choices. Refer to the parameter setting information in the SAT1 – First Satellite Parameters
paragraphs to set PRESET, NAME, LON, RHCP freq, BAUD, FEC, and NID for a third satellite that you wish to
use periodically.
2.3.8.
Access all of the SAT4 individual parameters via a sub menu. If a forth SAVED satellite is not needed, preset
SAT4 to empty/blank so
NEXT
will skip over this selection when you are switching satellites.
SAT4 - Fourth Satellite Parameters
All of the SAT4 parameters are set exactly the same way that the SAT1 parameters were set, but would be set
to different choices. Refer to the parameter setting information in the SAT1 – First Satellite Parameters
paragraphs to set PRESET, NAME, LON, RHCP freq, BAUD, FEC, and NID for a forth satellite that you wish to
use periodically.
2.3.9.
Access all of the SAT5 individual parameters via a sub menu. If a fifth SAVED satellite is not needed, preset
SAT5 to empty/blank so
NEXT will skip over this selection when you are switching satellites.
SAT5 - Fifth Satellite Parameters
All of the SAT5 parameters are set exactly the same way that the SAT1 parameters were set, but would be set
to different choices. Refer to the parameter setting information in the SAT1 – First Satellite Parameters
paragraphs to set PRESET, NAME, LON, RHCP freq, BAUD, FEC, and NID for a fifth satellite that you wish to
use periodically.
2.3.10.
Access all of the SAT6 individual parameters via a sub menu. If a sixth SAVED satellite is not needed, preset
SAT6 to empty/blank so
NEXT
will skip over this selection when you are switching satellites.
SAT6 - Sixth Satellite Parameters
All of the SAT6 parameters are set exactly the same way that the SAT1 parameters were set, but would be set
to different choices. Refer to the parameter setting information in the SAT1 – First Satellite Parameters
paragraphs to set PRESET, NAME, LON, RHCP freq, BAUD, FEC, and NID for a sixth satellite that you wish to
use periodically.
2.3.11.
Accessing the Factory Settings parameters should ONLY be done by a qualified technician from an
authorized Sea Tel dealer. The Antenna Model and Serial Number information is located on a sticker which
can be found on top of the electronics enclosure. The parameters are:
FACTORY SETTINGS
2.3.11.1. Serial Number
This parameter sets Serial Number of the Antenna Pedestal into the PCU memory. The serial
number starts with 98 followed by 6 digits that are editable. This parameter allows the serial number
of the antenna to be displayed on the display of the Antenna Control Panel during the initialization
process.