Sea Tel ST14 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 84

background image

ST14 Ku-Band TVRO

Installation

1-1

Possible Antenna Radome Assembly mounting locations

1.

Installation

Installation of your ST-14(D/E/M) Antenna system must be accomplished by or under the supervision of an
authorized Sea Tel dealer for the Sea Tel Limited Warranty to be valid and in force.

Good planning of the

installation will provide the best results. Below is some guidance on issues that are important to consider when planning the

installation.
Planning is the key to a good installation. Read the installation information below thoroughly before beginning the actual

installation. Then review your plan to adjust for any details that may have been overlooked.
A full scale Installation Template (drawing 126355) has been provided to locate the cutout areas and mounting holes for the

antenna radome and for the antenna control panel. The radome template section of the drawing includes the outer perimeter

of the radome base so you can insure that the radome will fit in the area chosen.

1.1.

Site Selection and Cable Routing Path

The best mounting location for the antenna radome assembly is where:

1.

The antenna has a clear line-of-sight view to as much of the sky as is practical. Choose a location where

masts or other structures do not block the satellite signal from the dish as the boat turns.

2.

The antenna is at least 5 feet away from other transmitting antennas (HF, VHF and radar) that may generate

signals that may interfere with the Coastal Series antenna. The further away the Coastal antenna is from

these other antennas, the less
impact their operation will have on

it.

3.

The antenna radome assembly

should be rigidly mounted to the

boat. If necessary, reinforce the

mounting area to assure that it
does not flex due to the boat

motion or vibration.

Choosing the best mounting location on

smaller boats, where there are fewer possible

locations to choose from, is frequently a

compromise. The Figure shown to the right
is provided to make some location

comparisons. The “poor” location is poor

because over half of the antenna’s viewable

sky is blocked by the overhang above it. The

“better” location has fewer blockages, but

the upper deck and the mast will cause some
blockage when the antenna is at lower

elevations. The “best” location has no

blockage from raised platforms, mast or the

body of the radar.
If enclosed in a cabinet or panel, assure that there is adequate airflow to prevent from over-heating and provide forced

airflow if needed.

«
...
5
6
7
8
9
...
»

Содержание ST14





















































































Отзывы:

Нет отзывов

Похожие инструкции для ST14

Бренд: M2 Страницы: 6

Taco Antenna D4000 Series

Бренд: WADE Antenna, Inc. Страницы: 9

Бренд: Chameleon Antenna Страницы: 11

Бренд: geo-FENNEL Страницы: 43

Бренд: Hughes Страницы: 20

Бренд: THOMSON Страницы: 38

Бренд: Televes Страницы: 4

Бренд: Gogen Страницы: 20

Бренд: Cabletech Страницы: 2

Бренд: PRO.SIS.TEL. Страницы: 7

Бренд: Sirio Antenne Страницы: 2

Бренд: Sirio Antenne Страницы: 4

Бренд: Sirio Antenne Страницы: 2

Бренд: Sirio Antenne Страницы: 2

SMP 4G LTE MiMo

Бренд: Sirio Antenne Страницы: 2

Бренд: Sirio Antenne Страницы: 2

Бренд: Sirio Antenne Страницы: 2

Бренд: Extreme Networks Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды