Schmitz 114.9600.0 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 88

Schmitz 114.9600.0 Скачать руководство пользователя страница 63

Instructions for use arco-matic 200 M / 300 M - Version 2018-05-08 GBR ID no. 2038823A

63

Pads

WARNING!

When used, pads absorb infectious germs which
can spread to other users. As a result, patients can
contract further illnesses. It is also important to
remember that infectious germs multiply extremely
quickly in unclean and undisinfected residues.
Therefore, clean and disinfect the pads before and
after use by the patient!

NOTE

Some solutions attack the surface of the pads.
For this reason, please remove skin disinfectants as
well as wound and mucous membrane disinfectants
as quickly as possible from the pad surface.

WARNING!

Damaged pads (e.g. slit or torn) often contain stub-
born infectious germs from normal use. These germs
cannot be completely removed even by means of
thorough disinfection. Upon contact with injuries or
open skin areas, the infectious germs can be trans-
ferred to the bloodstream of the patient and third
parties.
For this reason, always replace damaged pads
immediately!

NOTE

The surface of the pad can easily be damaged.
For this reason, keep pointed or sharp objects away
from the pads!

Dirty pads must be cleaned and disinfected without
delay. For hygienic reasons, replace damaged
replaceable pads immediately.
The use of “Cleaner 500” is recommended for
cleaning pads (cleaning set with brushes: art. no.
2026973, set of three bottles: art. no. 2019878).
Follow the instructions for use of the cleaning agent
(see http://cleaner.sergeferrari.com). As an alterna-
tive to “Cleaner 500” a weak alkaline detergent, e.g.
mild cleaning agent or soap and water, can be also
used.
If pads are disinfected with watery solutions,
residual organic salts must be removed regularly
(approximately every three months) to protect the
pad surfaces. In addition, use a cleaner with non-ion-
ogenic tensides or “Cleaner 500”.

Please also note the instruction sheet provided with
the pad concerning how to clean the pad.

«
...
61
62
63
64
65
...
»

Содержание 114.9600.0

























































































Отзывы:

Нет отзывов