Schmitz 114.9600.0 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 88

Schmitz 114.9600.0 Скачать руководство пользователя страница 16

16

Instructions for use arco-matic 200 M / 300 M - Version 2018-05-08 GBR ID no. 2038823A

Carrying

WARNING!

Components such as the foot rest or colposcopes
are not designed as carrying or lifting handles. When
subjected to such a load, the component will detach
from the examination chair. Serious injury may occur
when the examination chair falls as a result.
Components such as the foot rest or colposcopes
are not designed as carrying or lifting handles!

To carry the product after unpacking or fi nal use,
it must be brought into the transport position.

The transport position is the position in which the
product was delivered:

•

disconnected from the power supply,

•

no mounted accessories,

•

product moved down (height adjustment set to

lowest level).



Bring the product into the transport position.



Disconnect the mains connection (disconnect
the mains plug).



Detach mounted accessories.



Move the product to its lowest position.



During transportation, ensure that the unit does

not collide with persons or objects.

Setup

NOTE

The examination and treatment chair requires some
time to acclimatise. If the acclimatisation period is
too short, the examination and treatment chair may
be damaged.
For this reason, please let the examination and
treatment chair acclimate for at least 12 hours after
every transport.

NOTE

The power cord and supply cable for the foot control
unit may be damaged if the levelling screws touch
down on them.
For this reason, always make sure that none of
the electric cables are pinched under the levelling
screws or under the foot section.



Set up the unit so as to ensure that

•

the product can be used and operated without
any obstruction,

•

the mains plug is easily accessible,

•

the displays can be read easily, and

•

that existing switches can be operated easily
(e.g. the on/off switch at the rear must be
easily accessible).



Fit the removed foot supports (see “Attaching the

carry straps” on page 15) to the opposite side
to which they were previously fi tted.

«
...
14
15
16
17
18
...
»

Содержание 114.9600.0

























































































Отзывы:

Нет отзывов