Schmitz 114.9600.0 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 88

Schmitz 114.9600.0 Скачать руководство пользователя страница 55

Instructions for use arco-matic 200 M / 300 M - Version 2018-05-08 GBR ID no. 2038823A

55

Moving

The load placed on the examination and treatment
chair during motion must not exceed 160 kg .

RECOMMENDATION

It is recommended to push the examination and
treatment chair with the backside facing forwards
when moving it. This makes it easier to surmount
bumps in the ground.

RECOMMENDATION

Due to the fi xed double castors on the foot end, the
examination and treatment chair cannot be moved
in a transverse direction. When moving the chair, we
recommend swivelling out the head section to steer
the chair.



Bring the examination and treatment chair into the

transport position (see “Carrying” on page 16).



Lower the examination and treatment chair
fully.



Disconnect the mains plug.



Secure the power cord, foot control and foot
control cable.



Lift the pedal of the examination and treatment

chair up with your foot.

The examination and treatment chair is now ready
to be moved. Move the examination and treatment
chair to the desired location.
Never move the examination and treatment chair
with a patient on it!



The foot control must be repositioned at the new

location.



Reconnect the examination and treatment chair to

the mains supply.

While moving the product, please observe the
following:



During transportation, ensure that the unit does

not collide with persons or objects.

Locking



Push the pedal of the examination and treatment

chair down with your foot.

Position

Dynamic behaviour

Electrical conductivity

Front double castors

Fixed

Conductive

Rear double castors

Inclinable

Not conductive

Tab. 11
Features of the double castors

«
...
53
54
55
56
57
...
»

Содержание 114.9600.0

























































































Отзывы:

Нет отзывов