Schmitz 114.9600.0 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 88

Schmitz 114.9600.0 Скачать руководство пользователя страница 56

56

Instructions for use arco-matic 200 M / 300 M - Version 2018-05-08 GBR ID no. 2038823A

Foot rest for the doctor (right: 01.0468.0, left: 101.0469.0)

The foot rest allows the doctor to put his feet down.

Safe working load: see table in chapter “Approved
accessories” on page 7.

Mounting



Remove the panel from the right or left side of the

foot cover.



Insert the foot rest in the mount, as shown in Fig.

76.



Insert attachment screws and turn them tight.

Removal



Undo and remove the attachment screws.



Remove the foot rest.



Remount the panel on the right or left side of the

foot cover.

WARNING!

The foot rest is not designed to be used as a support
or lifting handle. When subjected to such a load,
the foot rest will release from the examination chair.
Serious injury may occur when the examination chair
falls as a result.
For this reason, do not use the foot rest as a support
or lifting handle!

WARNING!

The foot rest is designed to bear a load of up to 25
kg. If the foot rest is loaded with the entire body
weight of the patient (for example when getting in or
out of the chair) this may damage the foot rest and
lead to injury (such as sprains).
For this reason, make sure that patients do not use
the foot rest to help them get in or out of the chair!

Fig. 76
Foot rest for the doctor
1) Attachment screws

«
...
54
55
56
57
58
...
»

Содержание 114.9600.0

























































































Отзывы:

Нет отзывов