SATO XL 410e Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 80

SATO XL 410e Скачать руководство пользователя страница 80

Section 7: Optional Accessories

Page 7-6

XL400/410e Operator’s Manual

7.4 STACKER (CONT’D)

6. Turn the printer on and make sure the cutter is enabled and the tags aligned for printing.

Note:
If the tag sensors are not aligned properly, the printer feeds out a length of tag stock without

cutting it, as it is attempting to determine the tag pitch (length). Temporarily move the
Stacker unit to one side if this occurs, until the sensors are correctly set and the tags are at
the proper position. See Section 2 for instructions on loading and aligning the tags.

7. Send the print job to the printer and let it cut and stack a few tags. The temporarily stop the

printer by pressing the START/STOP key and check to make sure the tags are being
stacked under the Tag Hold Down and that the Tag Stop and Tag Edge Guide are prop-
erly set.

8. When proper operation has been verified, place the printer back ON LINE by pressing the

START/STOP key again to finish the print job.

9. The printer will automatically stop and go OFF LINE when the Stacker is full. When this hap-

pens, remove the tags and finish the print job by pressing the START/STOP key to place the
printer back ON LINE.

7.5 CALENDAR

The Calendar Option allows the date and time to be maintained in the local printer rather than
using the system clock. A qualified technician should perform the upgrade as it requires modifica-
tions to the main PCB assembly. Please call SATO Technical Support if you need to add this
option to an existing printer in the field.

«
...
78
79
80

Содержание XL 410e

















































































Отзывы:

Нет отзывов