manualshive.com logo in svg

SATO XL 410e, Руководство оператора, Страница: 79 / 80

Поделиться
Скачать
SATO XL 410e Скачать руководство пользователя страница 79

Section 7: Optional Accessories

XL400/410e Operator’s Manual

Page 7-5

Installation
The Stacker Option consists of four major components:

•    Stacker- The Stacker collects and stacks the tags as they are printed and cut.

•    Tag Stop - The Tag Stop is adjusted to the length of the label. It is magnetically held in 

place and should be adjusted for the length of the tags being stacked. A scale is pro-
vided for reference when making this adjustment.

•    Tag Edge Guide - The Tag Edge Guide should be adjusted for the width of the tag. It is 

held in place after adjustment by friction teeth on the Tag Stop.

•    Alignment Plate - The Alignment Plate is used to maintain proper alignment between 

the printer and the Stacker. The front two feet of the Stacker are aligned in the back 
two notches and the left two feet of the printer are aligned in the other two notches.

To install the Stacker on an XL Printer:

1. Turn the power off.

2. Place the Alignment Plate under the printer and align the two notches with the feet.

3. Place the Stacker on the Alignment Plate, aligning the other two notches with the Stacker feet.

4. Connect the attached interface cable to the EXT connector on the printer.

5. Adjust the Tag Stop for the length of the tag.

6. Adjust the Tag Edge Guide to the width of the tag.

TAG STOP

TAG SCALE

TAG HOLD DOWN

TAG EDGE GUIDE

Содержание XL 410e

















































































Отзывы:

Нет отзывов