SATO XL 410e Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 80

SATO XL 410e Скачать руководство пользователя страница 42

Section 3: Configuration

Page 3-8

XL400/410e Operator’s Manual

3.4 USER MODE

The LCD Panel on the XL400e and XL410e is used by the operator when manually entering
printer configuration settings. Many of the settings can also be controlled via software
commands, and in the case of conflict between software and control panel settings, the printer
will always use the last valid setting. If you load a label job that includes software settings and
then enter a new setting via the Operation Panel, the manually set values will be used by the
printer. If you set the values manually and then download a job with software settings, the
software settings will be used.

Pressing the FEED key will result in the printer now displaying the first USER mode
adjustment (Print Darkness).

Print Darkness Setting
There are three Darkness (or heat range) settings on the XL400e/410e (1, 2 and 3).
The higher numbers represent darker settings. The current setting is indicated by an
underline under one of the range settings. To change the setting:

1. Use the START/STOP key to step the underline cursor to the desired setting.

2. Once the correct setting is underlined, press the FEED key to advance to the next adjustment.

Note
This setting can be orverriden by software commands (see the section on Print Darkness on
page 5-49).

After setting the heat range with this command, finer adjustments can be made using
the PRINT potentiometer adjustment on the Adjustment panel. See page 4-1 for
additional information on how to make this adjustment.

USER MODE

print darkness
1 2 3

«
...
40
41
42
43
44
...
»

Содержание XL 410e

















































































Отзывы:

Нет отзывов