SATO XL 410e Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 80

SATO XL 410e Скачать руководство пользователя страница 45

Section 3: Configuration

XL400/410e Operator’s Manual

Page 3-11

3.5 SERVICE MODE

A Service Mode is provided to make adjustments that require only occasional changes. Since
they affect the basic operation of the printer, the procedure for entering this mode is designed to
prevent someone from accidently changing the settings.

To enter the Service Mode, the printer is powered on while pressing the START/STOP
simultaneously with the MEDIA TYPE key while powering the printer on.The printer will “beep”
one time and display the first configuration selection on the LCD panel. You select the type of
adjustment by pressing the START/STOP key. Each time the START/STOP key is pressed, the
Service Mode display will be cycled to the next selection. The type of adjustments that can be
made in the Service Mode are:

•   Sensor Setup
•   Pitch Offset
•   Cut Offset
•   Backfeed Offset
•   Clear Counter

From the Service Mode type display, the settings are accessed in sequence by pressing the
FEED key. Once you have cycled through all the adjustments for the Service Mode type,
pressing the FEED key will sequence you to the next Service Mode type.

«
...
43
44
45
46
47
...
»

Содержание XL 410e

















































































Отзывы:

Нет отзывов