SATO XL 410e Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 80

SATO XL 410e Скачать руководство пользователя страница 63

Section 5: Interface Specifications

XL400/410e Operator’s Manual

Page 5-3

5.3 THE RECEIVE BUFFER (CONT’D)

The receiving buffer will not be able to receive more data again until a “Buffer Available” condition
occurs. This takes place when the receiving buffer has emptied so that only 56K bytes of data
are being held (8K bytes from being full). At this time, DTR will go “high” or an X-On is sent to tell
the host that it can again receive data. All printer error conditions (i.e., label out, ribbon out) will
cause the printer to go busy (DTR “low” or X-Off) until the problem is corrected and the printer is
placed on-line. The printer will also be busy if taken off-line from the front panel.

5.4 RS232C SERIAL INTERFACE

General Specifications

Asynchronous ASCII

Half-duplex communication

Ready/Busy Hardware Flow Control
Pin 20, DTR Control
Pin 4, RTS Error Condition

X-On/X-Off Software Flow Control

Bi-Directional Communication (ENQ/Response)

Data Transmission Rate

2400, 4800, 9600 and 19200 bps

Character Format

1 Start Bit (fixed)
7 or 8 data bits (selectable)
Odd, Even or No Parity (selectable)
1 or 2 Stop bits (selectable)

Electrical Specifications
Connector DB-25S

(Female)

Cable

DB-25P (Male), 50 ft maximum length. For cable
configuration, refer to Cable Requirements appropriate
to the RS232C protocol chosen.

Signal Levels

High = +5V to +12V
Low = -5V to -12V

Pin 1

Pin 13

Pin 25

Pin 14

«
...
61
62
63
64
65
...
»

Содержание XL 410e

















































































Отзывы:

Нет отзывов