SATO XL 410e Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 80

SATO XL 410e Скачать руководство пользователя страница 38

Section 3: Configuration

Page 3-4

XL400/410e Operator’s Manual

3.1 PRINTER DIP SWITCH CONFIGURATION (CONT’D)

Receive Buffer Selection (DSW2-5): Selects the operating mode of the receive buffer. See
Section

5

: Interface Specifications for more information..

Reserved (DSW2-6): Reserved for future use.

Protocol Code Selection (DSW2-7): Selects the command codes used for protocol control.
Refer to Appendix E for more information.

Pitch Size Check (DSW2-8): Checks the length on the installed media against the
size loaded via software (<ESC>A1 Command, see the XL Series Programming Reference).

Reserved (DSW3): Reserved for future use.

Note
The Centronics (Parallel) communications port is always enabled regardless of the
settings for the RS232 port. There are no settings for Centronics. Both the Centronics
and RS232 ports are active at all times. Care should be taken to ensure that data is not
transmitted to both ports simultaneously as the received message will be corrupted.

DSW2-5

Setting

Off

Single Job

On

Multi Job

DSW2

ON

OFF

1

2

3

4

5

6

7

8

DSW2-7

Setting

Off

Standard

On

Non-Std

DSW2

ON

OFF

1

2

3

4

5

6

7

8

DSW2-7

Setting

Off

Disabled

On

Enabled

DSW2

ON

OFF

1

2

3

4

5

6

7

8

«
...
36
37
38
39
40
...
»

Содержание XL 410e

















































































Отзывы:

Нет отзывов