SATO XL 410e Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 80

SATO XL 410e Скачать руководство пользователя страница 36

Section 3: Configuration

Page 3-2

XL400/410e Operator’s Manual

3.1 PRINTER DIP SWITCH CONFIGURATION

DIP Switch Panels
Three DIP switches (DSW1, DSW2 and DSW3) are located underneath an access panel inside
the printer. These switches can be used to set:

• RS232C transmit/receive parameters

• Thermal transfer or direct thermal mode

• Head check mode

• Hex dump mode

• Receive buffer size

• Operation mode

Each switch is an eight section “toggle” switch. The ON position is always to the top (up). To set
the switches, first turn the unit Off, then position the DIP switches. After placing the switches in
the desired positions, turn the printer back on. The switch settings are read by the printer
electronics during the power up sequence. The settings will not become effective until the power
is cycled.

RS232 Transmit/Receive Setting
Data Bit Selection (DSW1-1): This switch sets the printer to receive either 7 or 8 bit data bits for
each byte transmitted.

Parity Selection (DSW1-2, DSW1-3): These switches select the type of parity used for error
detection.

DSW1-1

Setting

Off

8 data bits

On

7 data bits

DSW1

ON

OFF

1

2

3

4

5

6

7

8

DSW1-1

DSW1-3

Setting

Off

Off

No Parity

Off

On

Even

On

Off

Odd

On

On

Not Used

DSW1

ON

OFF

1

2

3

4

5

6

7

8

«
...
34
35
36
37
38
...
»

Содержание XL 410e

















































































Отзывы:

Нет отзывов