manualshive.com logo in svg

SATO XL 410e, Руководство оператора, Страница: 64 / 80

Поделиться
Скачать
SATO XL 410e Скачать руководство пользователя страница 64

Section 5: Interface Specifications

Page 5-4

XL400/410e Operator’s Manual

5.4 RS232C SERIAL INTERFACE (CONT’D)

Pin Assignments

READY/BUSY Flow Control
Ready/Busy is the hardware flow control for the serial interface on the XL printers. 

 

By raising/lowering the voltage level on Pin 20 of the RS232 port, the printer notifies the host 
when it is ready to receive data. Pin 4 (RTS) and pin 20 (DTR) are the important signals on the 
printer for this method of flow control. The host must be capable of supporting this flow control 
method for it to function properly.

RS232C Interface Signals

Pin

Direction

Signal Definition

1

Reference

FG (Frame Ground)

2

To Host

TD (Transmit Data) - Data from the printer to the host computer.

Sends X-On/X-Off characters or status data (Bi-Directional

protocol).

3

To Printer

RD (Receive Data) - Data to the printer from the host computer.

4

To Host

RTS (Request to Send) - Used with Ready/Busy flow control to 

indicate an error condition. RTS is high and remains high unless 
the print head is open (in this case, RTS would return to the high 
state after the print head is closed and the printer is placed back 

on-line) or an error condition occurs during printing (e.g., ribbon 

out, label out).

5

To Printer

CTS (Clear to Send) - When this line is high, the printer 

assumes that data is ready to be transmitted. The printer will not 

receive data when this line is low. If this line is not being used, it 

should be tied high (to pin 4).

6

To Printer

DSR (Data Set Ready) - When this line is high, the printer will be 

ready to receive data. This line must be high before data is

transmitted. If this line is not being used, it should be tied high 

(to pin 20).

7

Reference

SG (Signal Ground)

20

To Host

DTR (Data Terminal Ready) - This signal applies to Ready/Busy 
flow control. The printer is ready to receive data when this pin is 

high. It goes low when the printer is off-line, either manually or 

due to an error condition, and while printing in the Single Job 

Buffer mode. It will also go low when the data in the buffer 

reaches the Buffer Near Full level.

Содержание XL 410e

















































































Отзывы:

Нет отзывов