8
13
AUTODRIVE
Operation of the rear wheel drive (figure G )
Pos: 17.4 /Innente il/Fahra ntrieb/Be dienung des H inte rra dantriebes Tex t @ 0\mod _1115216328921_6.do cx @ 405 @ @ 1
The rear wheel drive is switched on and off using the drive control bar (1)
on the upper guide bar (2) while the engine is running:
-
Pull and hold the drive control bar = mower moves.
–
Release the drive control bar = mower stops (0 position).
Pos: 18.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_6.do cx @ 41 @ @ 1
Pos: 18.2 /Innente il/Mähbetrieb/ 1 MÄH BETRIEB @ 0\mod _1115358011109_6.d ocx @ 413 @ 1 @ 1
14
MOWING
Pos: 18.3 /Innente il/Siche rheitshinweise/ Sicherhe itshinweis: Lesen, Me sse r, Ste in, Absta nd, Moto rStop @ 0\mod_1115358236734_6.docx @ 415 @ @ 1
Safety information!
For explanation of symbols, see the
table on page 3
Pos: 18.4 /Innente il/Mähbetrieb/ 1.1 Mähen a n Hangla gen @ 0\mo d_1115358422453_6. docx @ 417 @ 2 @ 1
Using the machine on slopes
Pos: 18.5 /Innente il/Mähbetrieb/Mä hen an Hanglagen Sicherheitshinweis 25° Be nzin @ 38\mo d_1439983053439_6. docx @ 410855 @ @ 1
ATTENTION
The mower can be used on banks and slopes with a gradient of up to 46%
(25° angle). Any steeper slopes can lead to engine damage. For safety
reasons, however, we urgently recommend you do not exploit this theoretical
performance potential. Always make sure you have a firm stance. Walk-behind
lawn mowers should never be used for slopes with a gradient in excess of
26% (15° angle of slope). Stability may be lost!
Pos: 18.6 /Innente il/Mähbetrieb/ 1.1 Ölsta ndkontrolle @ 0\mod_1115358654859_6.docx @ 421 @ 2 @ 1
Checking the oil level
Pos: 18.7 /Innente il/Mähbetrieb/ Ölstandkontro lle Mähe r Text @ 0\mod _1115358693671_6.d ocx @ 423 @ @ 1
Check oil level before each mowing job
Y1
. Never let the engine run with too little
or too much oil. Irreparable damages could occur.
Pos: 18.8 /Innente il/Mähbetrieb/ 1.1 Prüfung de r Betriebssiche rheit @ 0\mod _1115358766390_6.do cx @ 425 @ 2 @ 1
Checking operating safety
Pos: 18.9 /Innente il/Mähbetrieb/P rüfung der Betrieb ssicherheit Text Benzin Seite nauswurf m. A. + Text DLG @ 53\mod_1513006606191_6.docx @ 577314 @ @ 1
The lawn mower is fitted with an engine stop device. Before every mowing job, make
sure that the engine stop safety control bar is working perfectly. When the control
bar is released, engine and cutter bar must come to a standstill within three
seconds. After release, the bar must always return to the position shown in the
“Description of components” diagram. If this is not the case, it must be checked
immediately by an authorised workshop.
Risk of injury!
If the stopping time of the blade is longer, stop using the device and take it to an
authorised workshop.
Measuring the stopping time
After starting the combustion engine, the blade rotates and a wind noise can be
heard. The stopping time corresponds to the duration of the wind noise after the
combustion engine has been switched off; it can be measured with a stopwatch.
Machine safety and protective devices must not be manipulated or disabled.
The correct operation of the autodrive control bar must also be checked before each
mowing job. When the autodrive control bar is released, the machine must come to
an immediate standstill. If this is not the case, it must be checked immediately by an
authorised workshop.
Make sure that all protective devices have been attached properly and are not
damaged.
To avoid any risk, always check the condition and firm seating of the blade before
each mowing job. The blade fastening screw must always be tightened by an
authorised workshop. If the blade screw is tightened excessively or insufficiently,
blade coupling and cutter bar may be damaged or get loose, which can lead to
serious injuries. A worn or damaged blade must imperatively be replaced. (See
chapter “Maintenance of the cutter bar”).
Check the blade coupling for wear and a tight fit every 10 operating hours. Also
check device screws and nuts for a firm fit and re-tighten, if necessary.
Make sure the spark plug connector is fitted tightly. Risk of electric shock. Never
remove the plug connector with the engine running. Risk of electric shock. Only
remove the plug connector if the engine has cooled down. Risk of burns.
If the mower becomes blocked e.g. by colliding with an obstacle, have an authorised
workshop check whether any parts of the mower are damaged or deformed. Always
have any necessary repairs done by an authorised workshop too.
If the machine starts to vibrate unusually heavily or to make unusual noises, please
have it checked immediately by an authorised workshop.
Pos: 18.10 / Innenteil/Mähbe trieb/1.1 Zeitliche Einschränkungen @ 0\mo d_1115358910000_6. docx @ 429 @ 2 @ 1
Time restrictions
Pos: 18.11 / Innenteil/Mähbe trieb/Zeitliche Einschränk ungen Deutschla nd Text @ 0\mod_1115358942500_6.docx @ 431 @ @ 1
In Germany, the time for the operation of lawn mowers is regulated in the "32nd
Ordinance for the Implementation of the Federal Immissions Act (32. BImSch-V)".
In addition, regional restrictions are possible (e.g. to observe the afternoon quiet
hours); related information is available from the competent municipal authority.
Pos: 18.12 / Innenteil/Mähbe trieb/1.1 Tipps zur Rase npflege @ 2\mod_1144832859503_6.docx @ 12192 @ 2 @ 1
Tips on caring for your lawn
Pos: 18.13 / Innenteil/Mähbe trieb/1.1 Mähe n (Abb ildung M) @ 2\mod _1144824073403_6.do cx @ 12091 @ 2 @ 1
Mowing (figure M )
Pos: 18.14 / Innenteil/Mähbe trieb/Tipp s zur Rasenpf lege Mähen H inweis @ 23\mod _1368694771094_6.do cx @ 173503 @ @ 1
WARNING
Remove all foreign bodies (stones, wood, branches, etc.) from the lawn before
any mowing; however, you should still keep an eye out for objects lying
around while mowing.
You can get an introduction to lawn care from your dealer on request. Information
and instructions for mowing can also be found on the manufacturer's website.
Pos: 18.15 / Innenteil/Mähbe trieb/1.1 Mulche n @ 2\mod_1144824162792_6.do cx @ 12101 @ 2 @ 1
Mulching
Pos: 18.16 / Innenteil/Mähbe trieb/Mulchen Hinweis Benzin Seitena uswurf @ 29\mod _1393239269069_6.d ocx @ 226867 @ @ 1
Your lawn mower can be equipped with a mulch kit. The corresponding conversion
kit to the mulch system is available from specialist dealers as an accessory (for the
order no. of the conversion kit, see "Original spare parts and accessories").
The mulch kit also includes tips and information on mulching. Information regarding
mulching can also be found on the manufacturer's website.
WARNING
Always have the mower converted to a mulch system by an authorised
specialist workshop. Due to an incorrectly assembled blade coupling or an
excessively or insufficiently tightened blade screw, the cutter bars may
become loose, which can lead to serious injuries.
And if the grass is too high for mulching, the mulching mower can be converted for
mowing with lateral ejection with only a few steps.
Pos: 18.17 / Innenteil/Mähbe trieb/1.1 Umba u auf Seitena uswurfmäher ( Abbildung R3) @ 3\mod_1153211248342_6.do cx @ 17702 @ 2 @ 1
Converting to lateral ejection mower (figure R3 )
Pos: 18.18 / Innenteil/Mähbe trieb/Umbau als Se itenauswurfmä her Tex t @ 38\mod _1439905860440_6.do cx @ 409725 @ @ 1
–
Stop the engine and remove the spark plug connector.
–
Remove the cover plate (1) on the right side of the housing. To do this, loosen
the two self-locking nuts (2) and remove the washers (3). From the inside
(cutting space), remove the two saucer-head screws (4) and remove the cover
plate.
Conversion of the mulching knife system is not necessary!
The cover plate (1) must be re-installed for the device to be used as mulching
mower again.
IMPORTANT
Before fitting the cover plate, clean the channel and remove any grass residue
and dirt from the inside of the housing to ensure that the plate can be seated
firmly and correctly.
From the inside, fit the cover plate into the housing in such a way that both bore
holes in the cover plate match the bore holes in the housing. Insert both saucer-
head screws (4) into the bore hole from the inside (cutting space), place the washers
(3) and fasten in place with the two self-locking nuts (2).
WARNING
Never use the device with the baffle plate damaged or missing.
Always work with the baffle plate closed (folded down), even if the device has
been converted for mulching.
Pos: 19.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_6.do cx @ 41 @ @ 1
Pos: 19.2 /Innente il/Wartungsintervalle/1 W ARTUNGSINTER VALLE @ 4\mo d_1159190053844_6. docx @ 20986 @ 1 @ 1
15
SERVICE INTERVALS
Pos: 19.3 /Innente il/Wartungsintervalle/Wartung sinte rvalle Wichtig @ 19\mod _1346242607856_6.do cx @ 148772 @ @ 1
IMPORTANT
Avoid damage! Under extreme or unusual conditions, shorter servicing
intervals than the ones specified below may be necessary. If you establish any
problems, please contact an authorised workshop.
Pos: 19.4 /Innente il/Wartungsintervalle/Wartung sinte rvalle Text @ 19\mo d_1346242427863_6. docx @ 147975 @ @ 1
Carry out routine servicing on the machine in line with the following servicing
intervals.
Work must be carried out at the following servicing intervals in addition to the
maintenance work listed in these operating instructions.
Pos: 19.5 /Innente il/Wartungsintervalle/Vo r der e rsten Inbetriebnahme Benzine r m. A. @ 28\mo d_1384501435310_6. docx @ 216692 @ @ 1
Содержание 52-S A
