rotork Insight 2 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 94

background image

55

Option Communication Loss Action

Configure how the actuator will respond to a loss of option communication. The available actions are:
Off: The communication loss action is turned off.
Open Action: The actuator will run to the open limit.
Close Action: The actuator will run to the closed limit.
Stop Action: The actuator will stop.
Go To Position Action: The actuator will run to a predetermined position.

Option Communication Loss Time

The user can specify the amount of time before a loss of communications is recognised as an alarm. This
is configurable between 0 and 65.

Coms Loss Timeout Scale

The units for Option Communication Loss Time can be adjusted from Milliseconds to Seconds to suit the
specific application.

Option Communications Loss Position (%)

Upon loss of communication to the option card, the actuator will move to this position. This is only
applicable if the actuator is configured to Go To Position on loss of communications. Position is shown
as a percentage of total travel.

6.10 Control Settings

6.10.1 Set Limits

Set Open Limit

This sets the open limit at the current position of the actuator.

Set Closed Limit

This sets the closed limit at the current position of the actuator.

«
...
53
54
55
56
57
...
»

Содержание Insight 2































































































Отзывы:

Нет отзывов

Похожие инструкции для Insight 2

Бренд: HAMAR LASER Страницы: 49

Бренд: EuroLite Страницы: 28

ST70 Instrument

Бренд: Raymarine Страницы: 12

Бренд: Raven Страницы: 73

Бренд: Tascam Страницы: 3

Бренд: RAB Lighting Страницы: 4

Бренд: campgo Страницы: 33

Chicken Coop Plan 3x5

Бренд: EASY COOPS Страницы: 21

Chicken Coop Plan 4x6

Бренд: EASY COOPS Страницы: 18

Chicken Coop Plan 8x10

Бренд: EASY COOPS Страницы: 18

Бренд: TC Electronic Страницы: 67

Бренд: Tascam Страницы: 3

Бренд: Mako Страницы: 17

BOS R254K-UUI-LH10-S4

Бренд: Balluff Страницы: 12

Бренд: Abbott Страницы: 64

Бренд: Gako Страницы: 22

Бренд: ABB Страницы: 38

Dome OnTop Weight

Бренд: ABS Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды