rotork Insight 2 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 94

background image

85

Set CPT Output

CPT (current position transmitter) is the analogue output signal that provides feedback of the current
actuator status. There are two available options for CPT output:
Position Output: Displays a 4-20mA (0-10V) signal scaled to the actuator position.
4mA (0V) = 0% and 20mA (10V) = 100%.
System Pressure:

Displays a 4-20mA (0-10V) signal scaled to the actuator system pressure.

4mA (0V) = 0% and 20mA (10V) = 100%.

Analogue Signal Failure Action

This dictates the actuator action if an analogue signal failure occurs. The three options are:
Alarm Off: The actuator will not present an alarm.
Alarm On: The actuator will present an alarm under loss of analogue signal.
Alarm and Software ESD:

The actuator will present an alarm and perform its Software ESD action (refer

to 8.5.1).

Deadband Closing (%)

This setting specifies the deadband for the analogue control signal in the close direction. The available
range is 0.1% to 9.9% at 0.1% increments.

Deadband Opening (%)

This setting specifies the deadband for the analogue control signal in the open direction. The available
range is 0.1% to 9.9% at 0.1% increments.

Hysteresis Closing (%)

This setting specifies the hysteresis for the analogue control signal in the close direction. The available
range is 0.1% to 9.9% at 0.1% increments.

Hysteresis Opening (%)

This setting specifies the hysteresis for the analogue control signal in the open direction. The available
range is 0.1% to 9.9% at 0.1% increments.

Minimum Percentage Demand (%)

The minimum demand required through the analogue input before the actuator will move away from
the closed limit. The available range is 0% to 9.9% at 0.1% increments.

8.6.2 Flow Characterisation

Flow Characterisation Enabled

This enables or disables flow characterisation. The analogue input for the SI Pro can be characterised to
suit the valve type. For example, equal percentage flow can be configured for the analogue input.

Demand input to position at (0% - 100%)

Each setting relates to an actuator position, every 5% across the full range of travel. The editable
setting value relates to a percentage of the analogue signal span (0% is 4mA or 0Vdc, 100% is 20mA or
10Vdc).

«
...
83
84
85
86
87
...
»

Содержание Insight 2































































































Отзывы:

Нет отзывов

Похожие инструкции для Insight 2

Бренд: Daavlin Страницы: 13

Бренд: Daavlin Страницы: 27

MicroVersaTrip Plus

Бренд: GE Страницы: 20

MicroVersaTrip Plus

Бренд: GE Страницы: 2

Бренд: GE Страницы: 252

Бренд: Balanced Body Страницы: 12

Бренд: Eagle Pro Страницы: 6

Бренд: GE Страницы: 10

Бренд: Abicor Binzel Страницы: 92

Бренд: Haag-Streit Страницы: 16

Бренд: Uchida Yoko Страницы: 40

EVENTWASH VL800

Бренд: Vari Lite Страницы: 23

Бренд: Vapotherm Страницы: 15

Бренд: Velp Scientifica Страницы: 16

Бренд: Velp Scientifica Страницы: 2

Бренд: Velp Scientifica Страницы: 32

Бренд: Velleman-Kit Страницы: 32

Бренд: Bartscher Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды