rotork Insight 2 Скачать руководство пользователя страница 30

Страница: 30 / 94

5.5.2 UPS Status Information

UPS Status Data (Raw Decimal Value)

For indication only, shows the raw decimal value that the UPS supplies to the actuator.

UPS Supply Voltage (V)

For indication only, shows the UPS supply voltage received by the actuator.

UPS Capacitor Voltages (V)

For indication only, shows the charge stored by each capacitor.

UPS Temperature Sensor Value (°C)

For indication only, shows the temperature measured at the UPS.

UPS Capacitor Values (Farads)

For indication only, shows the UPS capacitor values for all fitted capacitors.

UPS Capacitor Discharge Voltages (V)

For indication only, shows the separate discharge voltage for all fitted capacitors.

UPS End Discharge Voltage (V)

For indication only, shows the separate end discharge voltage for all fitted capacitors.

UPS Discharge Time (sec)

For indication only, shows the separate discharge time for each of the fitted capacitors.

5.6 CVA Status

5.6.1 Actuator Position (%)

For indication only, shows the position of the actuator as a percentage of full travel.

5.6.2 Actuator Torque (%)

For indication only, shows the percentage of rated torque currently measured through the actuator
drive train.

5.6.3 Analogue Demand Input (mA)

For indication only, shows the analogue input signal being received by the actuator.

5.6.4 Analogue Position Feedback (mA)

For indication only, shows the output signal being transmitted by the actuator with reference to
position or force (see 5.2.4).

5.6.5 ESD Input Status

For indication only, denotes whether the actuator ESD input is presently active or not.

Содержание Insight 2































































































Результаты поиска

Содержание Insight 2

Отзывы:

Похожие инструкции для Insight 2

Бренды по названию

Популярные бренды

rotork Insight 2, Руководство пользователя

Результаты поиска

Содержание Insight 2

Отзывы:

Похожие инструкции для Insight 2

Бренды по названию

Популярные бренды