rotork Insight 2 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 94

background image

45

6.3.3 Remote Configuration

Two Wire Priority

This sets the action the actuator will take when a close and open signal are applied simultaneously.
Open Priority: The actuator will run open if both signals are applied.
Stop Priority: The actuator will stay put or stop moving if both signals are applied.
Close Priority: The actuator will run closed if both signals are applied.

Interlock Mode

This sets the mode for the interlock inputs. Refer to the actuator wiring diagram for installation details.
To operate the actuator when an interlock mode is enabled, an interlock signal must be applied in the
appropriate direction whilst providing a control signal.
Disabled: The interlock inputs are disabled.
Interlocks Enabled: Interlocks are enabled for local and remote operation.
Conditional Control Enabled: Interlocks are enabled in remote control only.
Partial Stroke On Open Interlock Enabled: The open interlock will act as a remote input to initiate a
partial stroke test.

Fast Remotes (DC Only)

For indication only, this setting reduces the minimum required control signal pulse length. (Default
Setting: Disabled) Rotork Service Engineer use only.

Push to run past limit

This function will cause the actuator control signal to be Maintained once the actuator limit setting has
been passed. (Default: Enabled)

6.3.4 Local Configuration

Local Push to Run

When enabled this changes the local open/close control knob function to a push to run operation. The
knob position must be manually maintained for the actuator to run, upon removal of the signal the
actuator will stop.

Local Close Dominant Mode

For indication only, this setting means that when a local close control command is applied it will
override all other types of control. (Default: Disabled) Rotork Service Engineer use only.

Setting Tool Local Control

This setting enables the actuator to be controlled using the open, close and stop commands on the
setting tool.

Vandal Resist Mode

The vandal resist mode is aimed at preventing unauthorised actuator operation. There are four options
available.
Vandal Resist Off: All control knobs are active and the actuator will respond to all inputs, providing the
unit is in the correct control mode. (Default)
Vandal Resist Local: In this mode the local and remote controls are disabled. The actuator can only be
controlled by the open, close and stop commands on the setting tool.
Vandal Resist Remote: In this mode all local controls, including the setting tool, are disabled. The
actuator can only be controlled by remote inputs.
Vandal Resist Local/Remote Switch: Ignore this option as it is currently not a valid setting in the IQ
software.

«
...
43
44
45
46
47
...
»

Содержание Insight 2































































































Отзывы:

Нет отзывов

Похожие инструкции для Insight 2

Бренд: DARKSTAR TECHNOLOGIES Страницы: 4

Бренд: TDW Страницы: 2

Бренд: Taurus Страницы: 25

Бренд: Vancare Страницы: 3

Бренд: Paitec Страницы: 14

Бренд: Landoll Страницы: 6

Бренд: ParaBody Страницы: 9

Бренд: ParaBody Страницы: 3

Бренд: MacDon Страницы: 45

Бренд: H&S Страницы: 30

Бренд: OfiTE Страницы: 21

Бренд: Earthlite Страницы: 4

Бренд: YATEK Страницы: 78

WJHD100 - DIGITAL DISC RECORDE

Бренд: Panasonic Страницы: 7

Бренд: Paia Страницы: 11

Бренд: CAB Страницы: 39

Бренд: CAB Страницы: 27

Бренд: RayLight Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды