Rosemount OCX 8800, Инструкция по эксплуатации

Страница: 114 / 266

Instruction Manual
IM-106-880, Rev 2.1
April 2017
OCX 8800
7-14
COMB
_SENSOR_CAL_WHO
COMB_AUTOCAL_
INTERVAL
See FF-903 section 3.3.
0-9999 Hours The time between automatic calibrations of the combustibles sensor.
COMB_CAL_POINT 0-55000 PPM The value of the combustibles test gas.
COMB_CONSTANT -99.0-99.0 PPM The combustibles calibration constant.
COMB_DELTA_
RESISTANCE Ohms The raw value of the combustibles level input. This is the difference
between the active and reference RTDs.
COMB_FAILED_CONSTANT PPM This is the constant value calculated from the last failed Combustibles
calibration.
COMB_FAILED_SLOPE PPM/Ohm This is the slope value calculated from the last failed Combustibles
calibration.
COMB_HTR_DUTYCYCLE Combustibles heater duty cycle.
COMB_PERCENT_OF_
RANGE
COMB_PREVIOUS_
CONSTANT
% The percent of range of the current combustibles reading.
PPM The combustibles calibration constant from the previous good calibration.
COMB_PREVIOUS_SLOPE PPM/Ohm The combustibles calibration slope from the previous good calibration.
COMB_PRIMARY_VALUE The value and status of the combustibles concentration reading.
COMB_PRIMARY_VALUE_
RANGE
COMB_PRIMARY_VALUE_
TYPE
COMB_REFERENCE_
OHMS
COMB_SECONDARY_
VALUE
COMB_SECONDARY_
VALUE_RANGE
COMB_SENSOR_CAL_
DATE
COMB_SENSOR_
EXCITATION
See FF903
section 4.1
The High and Low range limit values, the engineering units code, and the
number of digits to the right of the decimal point for the combustibles
reading.
See FF-903 section 3.3.
Ohms The raw value of the combustibles reference input.
The combustibles cell temperature. This is the determined from the value
of the combustibles reference RTD.
The High and Low range limit values, the engineering units code, and the
number of digits to the right of the decimal point for the combustibles cell
temperature reading.
See FF-903 section 3.3.
mA Combustible Reference current.
COMB_SENSOR_TYPE See FF-903 section 3.3 and 4.3.
COMB_SETPOINT
°
C
Combustibles heater temperature set point.
COMB_SLOPE 200-4500 PPM/Ohm The combustibles calibration slope.
COMB_SLOPE_WARNING 25.0-99.0 % of FS The combustible slope warning threshold.
COMB_T90 0-300 Seconds The amount of time that the combustibles process variable will take to
reach 90% of the actual process variable.
COMB_TEMP_MAX °C The highest Combustibles temperature read since power on.
COMB_THERMOCOUPLE_
INPUT
COMB_TIME_TO_NEXT_
CAL
mV Combustible Block T/C voltage (Valid only with Type 3 sensor).
0-9999 Hours The time until the next automatic calibration of the combustibles sensor.
COMB_TOL_CHECK 0: No
– 1: Yes
Combustible calibration gas tolerance check.
COZERO_DURATION 120-600 Seconds The duration of the Combustibles sensor zero cycle.
COZERO_ENABLED 0: Off
– 1: On
Enumerated Indicates whether Combustibles sensor zero is enabled.
COZERO_INTERVAL 60-480 Minutes The time between Combustibles sensor zero cycles.
COZERO_OUTTRAK 0, 1, 2, 3 Enumerated Indicates whether the Combustibles analog output should track the input
during Combustibles sensor zero or lock at the last process reading.
(0=None, 1=O
2
, 2=CO
2
, 3= Both)
Parameter Mnemonic Valid Range Units Description