ROPA Tiger 5 Скачать руководство пользователя

Страница: 356 / 530

Maintenance and Service

Pump distributor gears (PDG)

356 / 530

– Remove the screw cap (

) of the intake hose from the filter connection. For this

purpose, you need a fork spanner SW 32.

– Loosen the hexagonal bolt connection (

) on the filter flange. The bolt connection

must only be loosened. In no case totally screw off this bolt connection. For this

purpose, you need a fork spanner SW 36.

– Screw out the 4 hexagonal recess bolts (

) on the filter connection (6 mm) and pull

out the filter element.

– Exchange the filter element for a new one (ROPA item no. O-20400010). When

installing, always use a new paper gasket (ROPA item no. O-20350003) and new

O-ring (ROPA item no. 412302). Before assembly, coat them with some oil.

– Retighten the bolt connection of flange and hose.

– Unscrew the oil drain hose again and screw on the screw cap again.

– Open the oil filler screw (

) and fill in fresh oil into the oil filling opening for so long,

until the oil level is in the upper range of the inspection glass.

Prescribed oil variants:

Gear oil ATF

ATF oil as per Dexron II D

Filling volume:

approx. 12.5 litres

Lubrication pump distributor gears failed!

– Start diesel engine and watch the R-Touch. The warning icon must disappear

from the R-Touch within 10 seconds.

– Let the diesel engine run for a minute, then shut it off.

– Wait at least 10 minutes, then again check the oil level – as described above, in

case of need, correct oil level.

Содержание Tiger 5



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание Tiger 5

Отзывы:

Похожие инструкции для Tiger 5

Бренды по названию

Популярные бренды

ROPA Tiger 5, Перевод оригинального руководства по эксплуатации

Результаты поиска

Содержание Tiger 5

Отзывы:

Похожие инструкции для Tiger 5

Бренды по названию

Популярные бренды