ROPA Tiger 5 Скачать руководство пользователя

Страница: 355 / 530

Maintenance and Service

Pump distributor gears (PDG)

355 / 530

7.2

Pump distributor gears (PDG)

The pump distributor gears is directly flanged to the diesel engine and transfers

engine power to the individual hydraulic pumps.

The oil level of the pump distributor gears must indispensably be checked daily. Check

the oil level, before you start the diesel engine! When the diesel engine has been

started, checking of the oil level is no longer possible.

To read the oil level, the machine must be standing on even and level ground and the

engine must have been shut off for at least 5 minutes. When the oil level rises or falls

without evident reason, indispensably call in a customer service mechanic.

The oil level can be read at the inspection glass (

). It must be within the inspection

glass range (in no case above the top edge of the inspection glass!). The inspection

glass is located on the left side of the pump distributor gears.

The gear oil is cooled by its individual oil cooler (

see page 357

(1)

Filler screw

(2)

Inspection glass

(3)

Oil drain valve

Optimal oil level

The first oil change is required after 50 operating hours. Thereafter, oil must be

changed annually. For each oil change, the intake filter of the pump distributor gears

must be replaced.
Proceed as follows for an oil and filter exchange:
– Clean before oil change wide area around the intake filter.

– Change oil only with gears warm after operation.

– Put an oil-resistant collecting vessel of sufficient size underneath.

– Open the closing cap at the oil drain valve (

) of the pump distributor gears.

– Screw the provided oil drain hose on the oil drain valve at the pump distributor

gears. The valve opens and the gear oil drains.

Содержание Tiger 5



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание Tiger 5

Отзывы:

Похожие инструкции для Tiger 5

Бренды по названию

Популярные бренды

ROPA Tiger 5, Перевод оригинального руководства по эксплуатации

Результаты поиска

Содержание Tiger 5

Отзывы:

Похожие инструкции для Tiger 5

Бренды по названию

Популярные бренды