ROPA Tiger 5 Скачать руководство пользователя

Страница: 351 / 530

Maintenance and Service

Diesel engine

351 / 530

7.1.4.4

Remarks of Mercedes-Benz on the cooling agent (general

information)

Normally, coolant consists of water and corrosion protection/antifreeze agent. The cor-

rosion protection/antifreeze agents (ethylene glycol with corrosion inhibitors) have the

following tasks in the cooling system:

Sufficient corrosion and cavitation protection for all components of the cooling sys-

tem.

Lowering of the freezing point (frost protection).

Raising of the boiling point.

For reasons of corrosion protection, about 50 vol.-% corrosion protection/antifreeze

agents must be added to the cooling liquid, if the expected environmental tempera-

tures do not require even higher concentration. This concentration (50 vol.-%) offers

antifreeze protection up to about -37°C. A higher concentration is only sensible for

even lower environmental temperatures. Even in case of extremely low environmen-

tal temperatures, do not use more than 55 vol.-% of corrosion protection/antifreeze

agents, since the maximum frost protection is achieved then, and greater share in the

mixture reduces frost protection and worsens heat dissipation (55 vol.-% corresponds

to frost protection up to about -45°C). If these coolant regulations are not complied

with, then corrosion and damage to the cooling system are inevitable. Adding of cor-

rosion protection/antifreeze agents raises the boiling point. Increased pressure further

increases the boiling temperature. Both physics coherences are used in modern cool-

ing systems – the maximum coolant temperature is increased without increasing the

hazard of boiling. Corresponding to the higher temperature level, the cooling perfor-

mance increases. Only approved products (MB sheet 325.5/326.5) offer reliable pro-

tection of the cooling system.

7.1.5

Valve clearance adjustment

Checking respectively adjusting of valve-clearance is required after the first

500 operating hours and then once annually respectively every 1500 operating hours.

This work may only be performed by people expressly authorized for this work by Mer-

cedes-Benz.
Valve clearance for cold engine:

Inlet valves 0.40mm +/- 0.05mm

Outlet valves 0.60mm +/- 0.05mm

Engine brake 4.60mm +/- 0.05mm

Содержание Tiger 5



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание Tiger 5

Отзывы:

Похожие инструкции для Tiger 5

Бренды по названию

Популярные бренды

ROPA Tiger 5, Перевод оригинального руководства по эксплуатации

Результаты поиска

Содержание Tiger 5

Отзывы:

Похожие инструкции для Tiger 5

Бренды по названию

Популярные бренды