ROPA Tiger 5 Скачать руководство пользователя | Manualshive

Страница: 303 / 530

background image

Operation

Hydraulic system

303 / 530

6.22

Hydraulic system

WARNUNG

The hydraulic system is under high pressure.

Hot hydraulic fluid may emit from leaks and cause severe injuries! The prestress of the

pressure reservoirs is present even when the remaining hydraulic system is already

pressureless. When dirt, even only in the smallest quantities, enters the hydraulic sys-

tem, this may lead to serious damage to the complete hydraulic system.
– Work on pressure reservoirs of the machine may only be performed by trained per-

sonnel.

– When working on the pressure reservoirs, the machine must first be rendered com-

pletely pressureless.

– The pressure reservoirs themselves may in no case be damaged or opened,

because substantial injuries to people can occur due to the constant prestress.

– During all work on the hydraulic system, ensure extreme cleanliness.

(1)

Hydraulic oil temperature

(2)

Hydraulic oil level

Regularly check the hoses of the hydraulic system for aging and damage! Immediately

exchange damaged or aged hoses. Only use original ROPA hoses or hoses fully con-

forming to the technical specifications of the original hoses! Observe the regionally

applying safety regulations on the service life of hydraulic hoses.
The hydraulic system is operational after the diesel engine has been started. To spare

the hydraulic system, the engine rotational speed during the first minutes (about

5 min.) after a cold start should in no case exceed the value of 1000 min-

1

. Even

higher rotational speeds for short times should be avoided. As long as the hydraulic

fluid has not reached normal operating temperature (longer times of standstill, low out-

side temperature), proceed as follows:
Let the engine warm up at 1000 min

-1

for about five minutes, until the hydraulic fluid

has reached a temperature of about 20° C. The temperature of the hydraulic fluid may

be read at the R-Touch at any time.

If the temperature of the hydraulic fluid is 70° C or higher, or when the icon is dis-

played on the R-Touch, immediately clean the hydraulic oil cooler.

«
...
301
302
303
304
305
...
»

Содержание Tiger 5



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger 5

Бренд: Falcon Страницы: 52

Бренд: Sagola Страницы: 8

Бренд: Tascam Страницы: 27

Бренд: Jay-Lor Страницы: 72

Бренд: MacDon Страницы: 198

Бренд: M-Triangel Страницы: 6

Бренд: Quincy lab Страницы: 4

Бренд: Paia Страницы: 11

Бренд: CAB Страницы: 39

Бренд: CAB Страницы: 27

Бренд: DANLERS Страницы: 2

Бренд: Haas Automation Страницы: 26

Бренд: Jacto Страницы: 12

Бренд: Ofa Bamberg Страницы: 80

Бренд: L-Acoustics Страницы: 5

Monkey Jump MM00125

Бренд: M&M Страницы: 2

REBOUND DUAL ST

Бренд: Össur Страницы: 104

Бренд: Össur Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды