ROPA Tiger 5 Скачать руководство пользователя

Страница: 475 / 530

Malfunction and Remedies

Towing

475 / 530

8.8

Towing

WARNUNG

By engine standstill the vehicle with rotating cardan shafts is steerable almost up to

standstill with increased effort on the steering wheel. The existing emergency steering

pump serves only for stopping action in case of diesel engine failure. Towing, thus, is

not allowed.
– Caution, if the brake is not functional! Only use vehicles with sufficient braking

power to tow the machine.

– For towing, use exclusively inflexible towing bars of sufficient dimensions. No other

vehicles may be towed or loads drawn using the machine itself.

If it should be necessary to tow the machine, then always observe the regional regula-

tions on the towing vehicle and on securing of the vehicle combination on public roads

and paths. Engage the parking brake and additionally secure the machine against

inadvertent rolling away using the four wedges attached to the bunker front wall. Notify

the nearest authorized customer service of ROPA. You need suitable salvaging aids

and tools.
– Remove the cardan shaft (

) between the reduction gears and the CVR gearbox.

The CVR gearbox has no switch position "neutral".

– Connect an appropriate salvaging aid e.g. a rigid towing bar (

see page 476

– Release the parking brake manually, (

see page 478

ADVICE

It is impossible to start the engine of the machine by towing or rolling.

Содержание Tiger 5



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание Tiger 5

Отзывы:

Похожие инструкции для Tiger 5

Бренды по названию

Популярные бренды

ROPA Tiger 5, Перевод оригинального руководства по эксплуатации

Результаты поиска

Содержание Tiger 5

Отзывы:

Похожие инструкции для Tiger 5

Бренды по названию

Популярные бренды