ROPA Tiger 5 Скачать руководство пользователя

Страница: 247 / 530

Operation

Lifter

247 / 530

Till vehicle identification number 6*1368

In machines with the vehicle identification number 6E* partially the volume controller

with hand wheel is installed. The hand wheel of the volume controller for manual

emergency adjustment of the rotational speed must always be completely turned out

(opened), because otherwise automatic control is no longer functional.

From vehicle identification number 6*1383

The volume controller can be actuated with an emergency pin.

6.14.14

Lifting rollers reverse

If lifting rollers one to five or one to six are blocked by a foreign object, this is indi-

cated on the R-Touch with the following warning icon: . An additional warning signal

sounds. In this case, the main lifter drive and driving power are automatically stopped.

To clear such a block, press the "Reverse main lifter drive" key (

) on the keypad III.

While this key is pressed, the defoliator shaft, leaf worm conveyor and lifting rollers

rotate backwards with reduced speed. When this key is released, the main lifter drive

automatically switches back to forward rotation.

DANGER

Hazard to life when working in or below the lifting unit.

– To remove the foreign object, completely lower the lifter, switch off the engine and

secure it against inadvertent restarting (lock driver's cabin door and keep the key

'on the man', e.g. in the pants pocket).

– Only then remove the blocking stone.

The main lifter drive may be operated from the ground by pressing the ground operat-

ing button (

) (e.g. for checking after remedy of a malfunction). If this key is pressed

twice in brief succession and held tight then, this drive is reversed. If the foreign object

can not be removed by reversal, then it must be removed using suitable tools (e.g. a

hammer).

Содержание Tiger 5



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание Tiger 5

Отзывы:

Похожие инструкции для Tiger 5

Бренды по названию

Популярные бренды

ROPA Tiger 5, Перевод оригинального руководства по эксплуатации

Результаты поиска

Содержание Tiger 5

Отзывы:

Похожие инструкции для Tiger 5

Бренды по названию

Популярные бренды