ROPA Tiger 5 Скачать руководство пользователя

Страница: 167 / 530

Operation

Road traffic

167 / 530

Further requirements for operating the machine:

Regardless of the time of day, the yellow rotating beacons must be switched on when

driving on public roads and streets.
Before driving on public roads and paths, the machine must be cleaned so far that:

the gross weight rating is not exceeded,

all warning signs are visible,

all direction indicators and lighting fixtures are clean and functional.

As a self-propelled processing machine with the highest driving speed of max.

40 km/h - 32 km/h or 25 km/h the machine is a subject to registration and license plate

duty. Furthermore, the vehicle must be insured against damage from vehicle owners‘

liability according to the locally applicable regulations.

The following conditions must always be fulfilled:

A guide giving the directions required for safe driving of the vehicle to the driver

must always be used, if otherwise safe driving of the vehicle (for instance at inter-

sections and road junctions, when backing up, or in case of unfavourable weather

conditions) cannot be ensured.

Rear wheel steering or U-turn may only be switched on for a short time for passing

narrow turns at low vehicle speed.

Only persons familiar with the vicinity, experienced and reliable may be used as

driver and accompanying personnel (guide).

The vehicle may only be moved on public roads and paths by drivers having the

required and valid driver's license. Besides the valid driver's licence, the driver also

has to carry originals of the general type approval of the machine and the existing

and valid exceptional permit.

Safety vests, first aid kit and warning triangle have to be carried with at hand.

No people may ride on the platform in front of the driver's cabin.

The vehicle owner or his representative have to instruct each driver before begin-

ning a working period about his special obligation for safe driving of the vehicle.

The instructions given must be acknowledged by the drivers with their signature.

The vehicle owner must keep these acknowledgements for at least one year. A

form for these instructions is included in Chapter 9 (

see page 519

). ROPA recom-

mends copying this form before completing it.

As already mentioned, the regionally competent road traffic authorities may estab-

lish additional conditions or conditions deviating from the regulations listed. It is the

sole responsibility of the vehicle owner and the driver to gain knowledge of these

regulations and to comply with them.

If parts or functions of the vehicle are subsequently modified, whose condition

respectively sequence has been prescribed, then "General type approval" lapses

and a new "General type approval" must be applied for with the authorities specific

to each country.

6.8.2

Additional chassis (option)

In order not to exceed the prescribed axle load on the public roads, e.g. in Federal

Republic of Germany, in certain states the machine has to be equipped with the addi-

tional chassis.

Содержание Tiger 5



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание Tiger 5

Отзывы:

Похожие инструкции для Tiger 5

Бренды по названию

Популярные бренды

ROPA Tiger 5, Перевод оригинального руководства по эксплуатации

Результаты поиска

Содержание Tiger 5

Отзывы:

Похожие инструкции для Tiger 5

Бренды по названию

Популярные бренды