Roland Sound Canvas SC-8850 Скачать руководство пользователя страница 142 | Manualshive

Страница: 142 / 256

background image

142

Appendices

Can’t install the SC-8850 USB driver (Windows 98)

●

Is USB enabled?

Enable USB on your computer.
If an unknown device is not detected when you first connect the SC-8850 to your
computer via a USB cable, it is possible that the USB interface itself is disabled.Use
the following procedure to check whether the USB interface is enabled.

1

Click the Windows [Start] button, and from [Settings], choose [Control Panel]. In
[Control Panel], double-click the [System] icon.

2

Click the [Device Manager] tab, and make sure that there are no yellow “!” marks or
“x” marks displayed beside [Universal serial bus controller] or [USB Root Hub] be-
low it.
If a yellow “!” mark or “x” mark is displayed, the USB is currently disabled.
Refer to the owner’s manual for your computer, and enable the USB.

●

Has an unknown device been registered?

If the SC-8850 USB driver installation is interrupted for some reason (such as
because a cable was pulled out) an unknown device could be registered to the
computer, and it may no longer possible to install the driver over again. If this oc-
curs, use the following procedure to delete the unknown device, and install the driv-
er once again.

1

Click the Windows [Start] button, and from [Settings], choose the [Control panel]. In
[Control panel], double-click the [System] icon.

2

Click the [Device manager] tab, and with [View devices by type] selected, make sure
that there is no [Other devices]. If there is, double-click it, and if there are any [Un-
known devices] below it, click to select them and then click the [Remove] button to
delete them.

3

Disconnect the USB cable from the SC-8850, and then re-connect the cable. If the
computer recognizes the SC-8850, perform the driver installation from the begin-
ning.

USB connections cannot be made correctly (Windows 98)

●

Has the SC-8850 been recognized?

Disconnect the USB cable, and then re-connect it.
It is possible that the computer has failed to recognize or initialize the SC-8850.
Leave the USB cable connected to the SC-8850, and restart Windows. If connection
still does not occur, exit Windows, and turn off the power of your computer.
Then turn on the power of your computer and start Windows.

Sound is distorted

●

Is an effect which distorts the sound being applied?

(p.93)

●

If a specific sound or Part is distorted, lower the volume level of that Part.

(p.32)

●

If all sounds are distorted, lower the overall volume level of all Parts

(p.50)

, or

use the [VOLUME] knob

(p.32)

to lower the volume level.

Pitch is incorrect

●

Is the pitch of a specific Part or all Parts incorrect?

(p.50, p.55)

●

Has the Fine Tune setting set to a specific Part?

(p.55)

●

Has a MIDI Pitch Bend message been received to change the pitch?

«
...
140
141
142
143
144
...
»

Содержание Sound Canvas SC-8850

































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sound Canvas SC-8850

Бренд: EMS Страницы: 48

Бренд: Roland Страницы: 54

Sequential Prophet-6

Бренд: Dave Smith Instruments Страницы: 92

Бренд: Keithley Страницы: 55

Бренд: Yamaha Страницы: 60

Бренд: Yamaha Страницы: 69

Бренд: Yamaha Страницы: 36

Бренд: Yamaha Страницы: 80

'14 Analogsynthesizer

Бренд: Vermona Страницы: 76

Бренд: nord Страницы: 233

Бренд: future.retro Страницы: 28

Бренд: future.retro Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды