Rockwell powerflex 700h Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 104

background image

3-8

Troubleshooting

113 Fatal App

➁

A Fatal Application error has
occurred.

1. Replace the Main Control board.

114 AutoT Enable

➁

Autotune is enabled but has
not started.

Press the Start key within 20 seconds
of enabling autotune.

120 I/O Change

➁

An option board has been
replaced.

Reset the fault.

121 I/O Comm Loss

➁

An I/O Board lost
communications with the
Main Control board.

1. Check the connector.

2. Check for induced noise.

3. Replace I/O board or Main Control

board.

133 DigIn CnflctA

➋

Digital input functions are in conflict. Combinations marked with a
“ ” will cause an alarm.

134 DigIn CnflctB

➋

A digital Start input has been configured without a Stop input or other
functions are in conflict. Combinations that conflict are marked with a
“ ” and will cause an alarm.

135 DigIn CnflctC

➋

More than one physical input has been configured to the same input
function. Multiple configurations are not allowed for the following
input functions.
Forward/Reverse

Run Reverse

Bus Regulation Mode B

Speed Select 1

Jog Forward

Acc2 / Dec2

Speed Select 2

Jog Reverse

Accel 2

Speed Select 3

Run

Decel 2

Run Forward

Stop Mode B

136 BipolarCnflct

➋

Parameter [Direction Mode] is set to “Bipolar” or “Reverse Dis” and
one or more of the following digital input functions is configured:
“Fwd/Reverse,” “Run Forward,” “Run Reverse,” “Jog Forward” or “Jog
Reverse.”

143 TB Man Conflict

➋

Parameter 96 [TB Man Ref
Sel] is using an analog input
that is programmed for
another function.

Check the parameter settings to
avoid problem.

147 Start AtPwrUp

➊

Parameter 168 [Start At PowerUp] is enabled. The drive may start at
any time within 10 seconds of drive powerup.

148 IntDB OvrHeat

➊

The drive has temporarily disabled the DB regulator because the
resistor temperature has exceeded a predetermined value.

No. Name

Fa

u

lt

Alarm Description

Action

(if appropriate)

* Jog 1 and Jog 2

Acc2/
Dec2

Accel 2 Decel 2 Jog*

Jog
Fwd

Jog
Rev

Fwd/
Rev

Acc2 / Dec2

Accel 2

Decel 2

Jog*

Jog Fwd

Jog Rev

Fwd/Rev

* Jog 1 and Jog 2

Start

Stop-
CF

Run

Run
Fwd

Run
Rev

Jog*

Jog
Fwd

Jog
Rev

Fwd/
Rev

Start

Stop-CF

Run

Run Fwd

Run Rev

Jog*

Jog Fwd

Jog Rev

Fwd/Rev

«
...
62
63
64
65
66
...
»

Содержание powerflex 700h









































































































Отзывы:

Нет отзывов

Похожие инструкции для powerflex 700h

Бренд: S&C Страницы: 40

Бренд: S&C Страницы: 34

Бренд: CAME Страницы: 12

Бренд: CAME Страницы: 16

Бренд: Ultrak Страницы: 41

Бренд: Zander Aachen Страницы: 10

Бренд: NEC Страницы: 146

Бренд: Rane Страницы: 2

Бренд: VAT Страницы: 26

Бренд: Zeta Страницы: 44

ArtNet-DMX Mux16

Бренд: DMX4ALL Страницы: 21

Бренд: Daihan Scientific Страницы: 11

phyCORE-MCF548x

Бренд: Phytec Страницы: 104

Red Atom PETRA01

Бренд: Perenio Страницы: 24

Temp Alert TA2HL

Бренд: Winland Electronics Страницы: 2

Бренд: Westfalia Страницы: 18

Бренд: FASAR ELETTRONICA Страницы: 2

Бренд: ACS Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды