Rockwell powerflex 700h Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 104

background image

3-12

Troubleshooting

Drive will not reverse motor direction.

Stopping the drive results in a Decel Inhibit fault.

Technical Support Options

Technical Support Wizards

If you are connected to a drive via DriveExplorer™ or DriveExecutive™,
you can run a Tech Support wizard to gather information that will help
diagnose problems with your drive and/or peripheral device. The
information gathered by the wizard is saved as a text file and can be emailed
to your remote technical support contact. (See

What You Need When You

Call Tech Support on page 3-13

for more information.)

To run a Tech Support wizard in DriveExplorer, select

Wizards

from the

Actions

menu. In DriveExecutive, select

Wizards

from the

Tools

menu. Or,

click the

button. Follow the prompts to complete the wizard.

Cause(s)

Indication

Corrective Action

Digital input is not selected for
reversing control.

None

Check [Digital Inx Sel],

correct input and program for reversing mode.

Digital input is incorrectly wired.

None

Check input wiring.

Direction mode parameter is
incorrectly programmed.

None

Reprogram [Direction Mode],

for

analog “Bipolar” or digital “Unipolar” control.

Motor wiring is improperly phased for
reverse.

None

Check for single phasing on the output of the
drive.

A bipolar analog speed command
input is incorrectly wired or signal is
absent.

None

1. Use meter to check that an analog input

voltage is present.

2. Check wiring.
Positive voltage commands forward direction.
Negative voltage commands reverse direction.

Cause(s)

Indication

Corrective Action

The bus regulation feature is
enabled and is halting deceleration
due to excessive bus voltage.
Excess bus voltage is normally due
to excessive regenerated energy or
unstable AC line input voltages.
Internal timer has halted drive
operation.

Decel Inhibit
fault screen.
LCD Status Line
indicates
“Faulted”.

1. See Attention statement on page

2. Reprogram parameters 161/162 to

eliminate any “Adjust Freq” selection.

3. Disable bus regulation (parameters 161 &

162) and add a dynamic brake.

4. Correct AC input line instability or add an

isolation transformer.

5. Reset drive.

«
...
66
67
68
69
70
...
»

Содержание powerflex 700h









































































































Отзывы:

Нет отзывов

Похожие инструкции для powerflex 700h

Бренд: Barthelme Страницы: 8

Бренд: CAB Страницы: 28

Бренд: C-TEC Страницы: 16

Бренд: C&T Solution Страницы: 27

SECURIT ST800L+

Бренд: C&K systems Страницы: 16

Бренд: IDTECK Страницы: 94

Бренд: MacDon Страницы: 32

Бренд: K&K Страницы: 6

Бренд: Unitech Страницы: 55

Бренд: S&C Страницы: 8

Бренд: UniPOS Страницы: 51

Бренд: Unipulse Страницы: 126

Бренд: YachtSafe Страницы: 3

SMARTSTART 6000

Бренд: Zener Страницы: 36

Бренд: Zapi Страницы: 5

Бренд: Paser Страницы: 2

Бренд: Computer Automation Technology Страницы: 55

Бренд: Roger Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды