Rockwell powerflex 700h Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 104

background image

Application Notes

B-17

Stop Modes

Mode

Description

Coast

This method releases the motor and allows the load to stop by friction.
1. On Stop, the drive output goes immediately to zero (off).

2. No further power is supplied to the motor. The drive has released control.

3. The motor will coast for a time that is dependent on the mechanics of the system

(inertia, friction, etc).

DC
Brake

This method uses DC injection of the motor to Stop and/or hold the load.
1. On Stop, 3 phase drive output goes to zero (off)

2. Drive outputs DC voltage on the last used phase at the level programmed in [DC Brake

Level] Par 158. This voltage causes a “stopping” brake torque. If the voltage is applied
for a time that is longer than the actual possible stopping time, the remaining time will be
used to attempt to hold the motor at zero speed.

3. DC voltage to the motor continues for the amount of time programmed in [DC Brake

Time] Par 159. Braking ceases after this time expires.

4. After the DC Braking ceases, no further power is supplied to the motor. The motor may

or may not be stopped. The drive has released control.

5. The motor, if rotating, will coast from its present speed for a time that is dependent on

the mechanics of the system (inertia, friction, etc).

Ramp

This method uses drive output reduction to stop the load.
1. On Stop, drive output will decrease according to the programmed pattern from its

present value to zero. The pattern may be linear or squared. The output will decrease to
zero at the rate determined by the programmed [Maximum Freq] and the programmed
active [Decel Time x]

2. The reduction in output can be limited by other drive factors such as such as bus or

current regulation.

3. When the output reaches zero the output is shut off.

4. DC voltage is applied to the motor for a time equal to [DC Brake Time] at [DC Brake

Level].

Coast Time is load dependent

Stop

Command

Time

Output Voltage

Output Current

Motor Speed

Stop

Command

DC Brake Time

(A)

(C)

(B)

Time

Output Voltage

Output Current

Motor Speed

DC

Brake Level

DC BrakeTime

DC

Brake

Level

Stop

Command

Time

Output Voltage

Output Current

Motor Speed

Output Voltage

Output Current

Zero

Command

Speed

«
...
91
92
93
94
95
...
»

Содержание powerflex 700h









































































































Отзывы:

Нет отзывов

Похожие инструкции для powerflex 700h

Бренд: Fairchild Страницы: 2

Бренд: Fagor Страницы: 103

Бренд: 3M Страницы: 34

Бренд: Dakota Digital Страницы: 6

CMD-2000 Series

Бренд: Dakota Digital Страницы: 10

Бренд: Z-Wave Страницы: 6

Бренд: Jands Страницы: 7

Бренд: hager Страницы: 11

coviva Smartbox TKP100A

Бренд: hager Страницы: 34

Бренд: Mamas & Papas Страницы: 44

Бренд: Mamas & Papas Страницы: 8

Бренд: Omegalink Страницы: 2

Бренд: MamaLove Страницы: 9

Бренд: Nacon Страницы: 24

Бренд: NAD Страницы: 4

Бренд: NAD Страницы: 4

Бренд: YASKAWA Страницы: 49

Бренд: M-system Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды