Rockwell powerflex 700h Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 104

background image

B-14

Application Notes

Sleep Wake Mode

This function stops (sleep) and starts (wake) the drive based on separately
configurable analog input levels rather than discrete start and stop signals.
by default, this function is disabled. The following Sleep/Wake modes are
available:

•

1 “Direct” - In this mode, the drive will start (wake) when the analog
input signal is greater than or equal to the value set in [Wake Level] and
the drive will stop (sleep) when the analog input signal is less than or
equal to the value in [Sleep Level].

•

2 “Invert” - In this mode, the analog input signal used by the [Wake
Level] and [Sleep Level] parameters is inverted. In this mode, the drive
will start (wake) when the analog input signal is less than or equal to the
value set in [Wake Level] and the drive will stop (sleep) when the analog
input signal is greater than or equal to the value in [Sleep Level].

Definitions

•

Wake - A start command generated when the analog input value remains
above [Wake Level] for a time greater than [Wake Time].

•

Sleep - A Stop command generated when the analog input value remains
below [Sleep Level] for a time greater than [Sleep Time].

•

Speed Reference – The active speed command to the drive as selected by
drive logic and [Speed Ref x Sel].

•

Start Command - A command generated by pressing the Start button on
the HIM, closing a digital input programmed for Start, Run, Run
Forward or Run Reverse.

«
...
88
89
90
91
92
...
»

Содержание powerflex 700h









































































































Отзывы:

Нет отзывов

Похожие инструкции для powerflex 700h

Бренд: T-Verter Страницы: 121

Бренд: Happy Страницы: 10

Бренд: Zolix Instruments Страницы: 22

Бренд: UniKey Страницы: 20

Бренд: Yudian Страницы: 26

Бренд: Easy-Laser Страницы: 84

Бренд: Easy Heat Страницы: 4

Бренд: Parkside Страницы: 65

Бренд: Xilinx Страницы: 2

Бренд: Parker Страницы: 16

Бренд: ZKTeco Страницы: 2

Бренд: ABB Страницы: 17

Бренд: Zaiput Flow Technologies Страницы: 10

Бренд: Valco baby Страницы: 8

Бренд: Fluidmaster Страницы: 2

Бренд: KEY Страницы: 16

Бренд: Belimo Страницы: 2

Бренд: Watts Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды