manualshive.com logo in svg

Rockwell Automation PowerFlex 750-Series, Руководство пользователя

Поделиться
Скачать
Rockwell Automation PowerFlex 750-Series Скачать руководство пользователя страница 25

 

 

 

PowerFlex 750-Series Drive DeviceNet Option Module User Manual

Publication 750COM-UM002A-EN-P

Chapter

 3

Configuring the Option Module

This chapter provides instructions and information for setting the 
parameters to configure the Option Module.  

For a list of parameters, refer to 

Appendix B

, 

Option Module 

Parameters

. For definitions of terms in this chapter, refer to the 

Glossary

.

Configuration Tools

The Option Module stores parameters and other information in its own 
non-volatile memory. You must, therefore, access the Option Module to 
view and edit its parameters. The following tools can be used to access 
the Option Module parameters:  

Important: For the HIM screens shown throughout this chapter, the 

Option Module is assumed to be installed in drive Port 04. 
If your Option Module is installed in a different drive port, 
that port would appear instead of Port 04.

Using the Enhanced 
PowerFlex 7-Class HIM

If your drive has an enhanced PowerFlex 7-Class HIM, it can be used to 
access parameters in the Option Module. For details on viewing and 
editing parameters, refer to the Enhanced PowerFlex 7-Class HIM User 
Manual (publication 20HIM-UM001).

Topic

Page

Configuration Tools

3-1

Using the Enhanced PowerFlex 7-Class HIM

3-1

Using the HIM to Access Parameters in the Option Module

3-2

Setting the Node Address

3-2

Setting the Data Rate

3-2

Setting a Master-Slave Hierarchy (Optional)

3-3

Selecting COS, Cyclic or Polled (Optional)

3-5

Setting a Fault Action

3-7

Resetting the Option Module

3-8

Restoring Option Module Parameters to Factory Defaults

3-9

Viewing the Option Module Status Using Parameters

3-10

Flash Updating the Option Module

3-11

Tool

Refer to…

Enhanced PowerFlex 7-Class HIM

Enhanced PowerFlex 7-Class HIM User Manual

DriveExplorer Software 
(version 6.01 or higher)

http://www.ab.com/drives/driveexplorer, or 
DriveExplorer online help (installed with the software)

DriveExecutive Software 
(version 5.01 or higher)

http://www.ab.com/drives/drivetools, or 
DriveExecutive online help (installed with the software)

Содержание PowerFlex 750-Series

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды