manualshive.com logo in svg

Rockwell Automation PowerFlex 750-Series, Руководство пользователя

Поделиться
Скачать
Rockwell Automation PowerFlex 750-Series Скачать руководство пользователя страница 134

G-6

Glossary

PowerFlex 750-Series Drive DeviceNet Option Module User Manual

Publication 750COM-UM002A-EN-P

 

 

 

Polled I/O Data Exchange

A device that is configured for polling I/O data exchange sends data 
immediately after it receives a request for the data. For example, an 
Option Module receives a Logic Command from the scanner and then 
sends back the Logic Status of the connected PowerFlex drive.

PowerFlex 750-Series (Architecture Class) Drives

Allen-Bradley PowerFlex 750-Series drives are part of the PowerFlex 
7-Class family of drives.

Producer/Consumer Network

On producer/consumer networks, packets are identified by content 
rather than an explicit destination. If a node needs the packet, it will 
accept the identifier and consume the packet. The source therefore 
sends a packet once and all the nodes consume the same packet if they 
need it. Data is produced once, regardless of the number of consumers. 
Also, better synchronization than Master-Slave networks is possible 
because data arrives at each node at the same time

R

Reference/Feedback

The Reference is used to send a setpoint (for example, speed or 
frequency) to the drive. It consists of one 32-bit REAL (floating point) 
piece of output control data from the network to the Option Module.

Feedback is used to monitor the speed of the drive. It consists of one 
32-bit REAL (floating point) piece of input control data from the 
Option Module to the network.

RSLogix 5000

RSLogix 5000 software is a tool for configuring and monitoring 
controllers to communicate with connected devices. It is an application 
that runs on various Windows operating systems. Information about 
RSLogix software can be found at 

http://www.software.rockwell.com/

rslogix

.

S

Scanner

A scanner is a separate module (of a multi-module controller) or a 
built-in component (of a single-module controller) that provides 
communication with Option Modules connected to a network. See also 
Controller.

SI (Serial Interface)

A next generation communication interface used by various 
Allen-Bradley drives, such as PowerFlex 750-Series drives.

Status Indicators

Status indicators are LEDs that are used to report the status of the 
Option Module, network, and drive. They are on the Option Module and 
can be viewed when the drive is powered and its cover is removed.

Содержание PowerFlex 750-Series

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды