manualshive.com logo in svg

Rockwell Automation PowerFlex 750-Series, Руководство пользователя

Поделиться
Скачать
Rockwell Automation PowerFlex 750-Series Скачать руководство пользователя страница 31

Configuring the Option Module

3-7

 

 

 

PowerFlex 750-Series Drive DeviceNet Option Module User Manual

Publication 750COM-UM002A-EN-P

Setting a Fault Action

By default, when I/O communications are disrupted (for example, the 
network cable is disconnected), the controller is idle (in program mode 
or faulted) or explicit messaging for drive control is disrupted, the drive 
responds by faulting. You can configure a different response to:

•

Disrupted I/O communication by using Host Parameter 33 - 
[Comm Flt Action].

•

An idle controller by using Host Parameter 34 - [Idle Flt Action].

•

Disrupted explicit messaging for drive control via PCCC and the CIP 
Register Object by using Host Parameter 35 - [Msg Flt Action].

Changing the Fault Action

Set the values of Host Parameters 33 - [Comm Flt Action], 34 - [Idle 
Flt Action], and 35 - [Msg Flt Action] to the desired responses:  

Figure 3.7

Edit Fault Action HIM Screens  

Changes to these parameters take effect immediately. A reset is not 
required.

!

ATTENTION:  Risk of injury or equipment damage exists. 
Host Parameters 33 - [Comm Flt Action], 34 - [Idle Flt 
Action], and 35 - [Msg Flt Action] let you determine the 
action of the Option Module and connected drive if I/O 
communication is disrupted, the controller is idle, or explicit 
messaging for drive control is disrupted. By default, these 
parameters fault the drive. You can set these parameters so 
that the drive continues to run. Precautions should be taken to 
ensure that the settings of these parameters do not create a 
risk of injury or equipment damage. When commissioning the 
drive, verify that your system responds correctly to various 
situations (for example, a disconnected network cable, 
controller in idle state or explicit message control disruption).

Value Action

Description

0

Fault

The drive is faulted and stopped. (Default)

1

Stop

The drive is stopped, but not faulted.

2

Zero Data

The drive is sent 0 for output data. This does not command a stop.

3

Hold Last

The drive continues in its present state.

4

Send Flt Cfg The drive is sent the data that you set in the fault configuration 

parameters (Host Parameters 37 - [Flt Cfg Logic], 38 - [Flt Cfg Ref], 
and 39 - [Flt Cfg DL 01] through 54 - [Flt Cfg DL 16]).

ESC

ENTER

Stopped
0.00 Hz

AUTO

F

▲

▼

Edit Comm Flt Action

Fault

0

0 << 4

ESC

ENTER

Stopped
0.00 Hz

AUTO

F

▲

▼

Edit Idle Flt Action

Fault

0

0 << 4

ESC

ENTER

Stopped
0.00 Hz

AUTO

F

▲

▼

Edit Msg Flt Action

Fault

0

0 << 4

Содержание PowerFlex 750-Series

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды