manualshive.com logo in svg

Rockwell Automation PowerFlex 750-Series, Руководство пользователя

Поделиться
Скачать
Rockwell Automation PowerFlex 750-Series Скачать руководство пользователя страница 80

7-2

Troubleshooting

 

 

 

PowerFlex 750-Series Drive DeviceNet Option Module User Manual

Publication 750COM-UM002A-EN-P

PORT Status Indicator

Status

Cause

Corrective Action

Off

The Option Module is not powered 
or is not properly connected to the 
drive.

•

Securely connect and ground the Option 
Module to the drive by fully inserting it into the 
drive port and tightening its two captive 
screws to the recommended torque.

•

Apply power to the drive.

Flashing 
Red

The Option Module is not receiving 
a ping message from the drive or 
the Option Module is not logged in.

Cycle power to the drive.

Solid 
Red

The drive has refused an I/O 
connection from the Option Module.

Another DPI peripheral is using the 
same DPI port as the Option 
Module.

Important: Cycle power to the drive after 
making any of the following corrections:

•

Securely connect and ground the Option 
Module to the drive by fully inserting it into the 
drive port and tightening its two captive 
screws to the recommended torque.

•

Verify that the drive supports the Comm 
Driver.

Orange

The brand of the Option Module 
and drive do not match.

Connect the Option Module to a product of the 
same brand (for example, an Allen-Bradley 
PowerFlex 750-Series drive).

Flashing 
Green

The Option Module is establishing 
an I/O connection to the drive.

No action required. Normal behavior if no I/O is 
enabled.

Solid 
Green

The Option Module is properly 
connected and is communicating 
with the drive.

No action required.

Содержание PowerFlex 750-Series

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды