manualshive.com logo in svg

Rockwell Automation PowerFlex 750-Series, Руководство пользователя

Поделиться
Скачать
Rockwell Automation PowerFlex 750-Series Скачать руководство пользователя страница 14

1-4

Getting Started

 

 

 

PowerFlex 750-Series Drive DeviceNet Option Module User Manual

Publication 750COM-UM002A-EN-P

Safety Precautions

Please read the following safety precautions carefully

. 

 

!

ATTENTION:  Risk of injury or death exists. The 
PowerFlex drive may contain high voltages that can cause 
injury or death. Remove all power from the PowerFlex drive, 
and then verify power has been discharged before installing 
or removing an Option Module.

!

ATTENTION:  Risk of injury or equipment damage exists. 
Only personnel familiar with drive and power products and the 
associated machinery should plan or implement the 
installation, start up, configuration, and subsequent 
maintenance of the drive using an Option Module. Failure to 
comply may result in injury and/or equipment damage.

!

ATTENTION:  Risk of equipment damage exists. The 
Option Module contains ESD (Electrostatic Discharge) 
sensitive parts that can be damaged if you do not follow ESD 
control procedures. Static control precautions are required 
when handling the Option Module. If you are unfamiliar with 
static control procedures, refer to Guarding Against 
Electrostatic Damage (publication 8000-4.5.2).

!

ATTENTION:  Risk of injury or equipment damage exists. 
If the Option Module is transmitting control I/O to the drive, 
the drive may fault when you reset the Option Module. 
Determine how your drive will respond before resetting the 
module.

!

ATTENTION:  Risk of injury or equipment damage exists. 
Host Parameters 33 - [Comm Flt Action], 34 - [Idle Flt 
Action], and 36 - [Msg Flt Action] let you determine the 
action of the Option Module and connected drive if I/O 
communication is disrupted, the controller is idle, or explicit 
messaging for drive control is disrupted. By default, these 
parameters fault the drive. You can set these parameters so 
that the drive continues to run. Precautions should be taken to 
ensure that the settings of these parameters do not create a 
risk of injury or equipment damage. When commissioning 
the drive, verify that your system responds correctly to 
various situations (for example, a disconnected cable or a 
controller in idle state).

!

ATTENTION:  Risk of injury or equipment damage exists. 
When a system is configured for the first time, there may be 
unintended or incorrect machine motion. Disconnect the 
motor from the machine or process during initial system 
testing.

!

ATTENTION:  Risk of injury or equipment damage exists. 
The examples in this publication are intended solely for 
purposes of example. There are many variables and 
requirements with any application. Rockwell Automation, 
Inc. does not assume responsibility or liability (to include 
intellectual property liability) for actual use of the examples 
shown in this publication.

Содержание PowerFlex 750-Series

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды