manualshive.com logo in svg

Rockwell Automation PowerFlex 750-Series, Руководство пользователя

Поделиться
Скачать
Rockwell Automation PowerFlex 750-Series Скачать руководство пользователя страница 89

 

 

 

PowerFlex 750-Series Drive DeviceNet Option Module User Manual

Publication 750COM-UM002A-EN-P

Appendix

 B

Option Module Parameters

Appendix B provides information about the Option Module parameters.  

Parameter Types

The Option Module has two types of parameters:

•

Device parameters are used to configure the Option Module to 
operate on the network. Device parameters, when viewed using 
DriveExplorer or DriveExecutive, appear below the 20-750-DNET 
listing in the treeview in a separate Device Parameters folder . When 
viewed using the HIM, these parameters appear in the DEV PARAM 
folder.

•

Host parameters are used to configure the Option Module Datalink 
transfer and various fault actions with the drive. Host parameters, 
when viewed using DriveExplorer or DriveExecutive, appear below 
the 20-750-DNET listing in the treeview in a separate Host 
Parameters folder. When viewed using the HIM, these parameters 
appear in the HOST PARAM folder.

About Parameter Numbers

Each parameter set is independently and consecutively numbered.  

How Parameters Are 
Organized

The Device Parameters and Host Parameters are separately displayed in 
a Numbered List view order.

Topic

Page

Parameter Types

B-1

About Parameter Numbers

B-1

How Parameters Are Organized

B-1

Device Parameters

B-2

Host Parameters

B-4

Configuration Tool

Numbering Scheme

•

HIM

•

DriveExplorer

•

DriveExecutive

The Device parameters and Host parameters begin with parameter 
01. For example, Device Parameter 01 - [Port Number] and Host 
Parameter 01 - [Net to Drv DL 01] are parameter 01 as indicated 
by this manual.

•

Explicit Messaging

Refer to 

Chapter 6

, 

Using Explicit Messaging

 and 

Appendix C

, 

DeviceNet Objects

 for details.

Содержание PowerFlex 750-Series

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды