manualshive.com logo in svg

Rockwell Automation PowerFlex 750-Series, Руководство пользователя

Поделиться
Скачать
Rockwell Automation PowerFlex 750-Series Скачать руководство пользователя страница 90

B-2

Option Module Parameters

 

 

 

PowerFlex 750-Series Drive DeviceNet Option Module User Manual

Publication 750COM-UM002A-EN-P

Device Parameters

Parameter
No. Name and Description

Details

01 [Port Number]

Displays the drive port into which the Option 
Module is installed. Typically, this will be Port 
4, 5 or 6.

Default:

5

Minimum:

0

Maximum:

7

Type:

Read Only

02 [DLs From Net Cfg]

Sets the number of contiguous controller-to- 
drive Datalinks (additional parameters) that 
are included in the network I/O connection. 
Logic Command and Reference are always 
included in the I/O connection. This parameter 
controls how many of the contiguous Host [DL 
From Net xx] parameters (16 maximum) are 
active. For example, if this parameter value is 
set to “5,” then Host Parameters 01 - [DL 
From Net 01] through 05 - [DL From Net 05] 
will be updated.

Default:

0

Minimum:

0

Maximum:

16

Type:

Read/Write

Reset Required:

Yes

03 [DLs From Net Act]

Displays the value of Device Parameter 02 - 
[DLs From Net Cfg] at the time the drive was 
reset. This is the number of actual contiguous 
controller-to-drive Datalinks that the drive is 
expecting.

Default:

0

Minimum:

0

Maximum:

16

Type:

Read Only

04 [DLs To Net Cfg]

Sets the number of contiguous drive-to- 
controller Datalinks (additional parameters) 
that are included in the network I/O 
connection. Logic Status and Feedback are 
always included in the I/O connection. This 
parameter controls how many of the 
contiguous Host [DL To Net xx] parameters 
(16 maximum) are active. For example, if this 
parameter value is set to “5,” then Host 
Parameters 17 - [DL To Net 01] through 21 - 
[DL To Net 05] will be updated.

Default:

0

Minimum:

0

Maximum:

16

Type:

Read/Write

Reset Required:

Yes

05 [DLs To Net Act]

Displays the value of Device Parameter 04 - 
[DLs To Net Cfg] at the time the drive was 
reset. This is the number of actual contiguous 
drive-to-controller Datalinks that the controller 
is expecting.

Default:

0

Minimum:

0

Maximum:

16

Type:

Read Only

06 [Net Addr Src]

Displays the source from which the Option 
Module node address is taken. This will be 
either the Node Address switches (see 

Figure 2.1 on page 2-2

) or the value of Device 

Parameter 07- [Net Addr Cfg].

Default:

0 = Switches

Values:

0 = Switches
1 = Parameters

Type:

Read Only

07 [Net Addr Cfg]

Sets the network node address for the Option 
Module if Device Parameter 06 - [Net Addr 
Src] is set to “1” (Parameters).

Default:

63

Minimum:

0

Maximum:

63

Type:

Read/Write

Reset Required:  Yes

08 [Net Addr Act]

Displays the actual network node address 
used by the Option Module.

Default:

63

Minimum:

0

Maximum:

63

Type:

Read Only

Содержание PowerFlex 750-Series

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды