manualshive.com logo in svg

Rockwell Automation PowerFlex 750-Series, Руководство пользователя

Поделиться
Скачать
Rockwell Automation PowerFlex 750-Series Скачать руководство пользователя страница 32

3-8

Configuring the Option Module

 

 

 

PowerFlex 750-Series Drive DeviceNet Option Module User Manual

Publication 750COM-UM002A-EN-P

Setting the Fault Configuration Parameters

If you set Host Parameter 33 - [Comm Flt Action], 34 - [Idle Flt 
Action] or 35 - [Msg Flt Action] to “Send Flt Cfg,” the values in the 
following parameters are sent to the drive after an I/O communications 
fault, idle fault, and/or explicit messaging for drive control fault occurs. 
You must set these parameters to values required by your application.  

Changes to these parameters take effect immediately. A reset is not required.

Resetting the Option 
Module

Changes to switch settings and some Option Module parameters require 
you to reset the Option Module before the new settings take effect. You 
can reset the Option Module by power cycling the drive or by using 
Device Parameter 14 - [Reset Module].  

Set Device Parameter 14 - [Reset Module] to “1” (Reset Module).

Figure 3.8

Edit Reset Module HIM Screen  

When you enter “1” (Reset Module), the Option Module will be 
immediately reset. An alternate method to reset the module is by power 
cycling the drive. When you enter “2” (Set Defaults), the Option 
Module will set ALL of its Device and Host parameters to their factory 
default values. (This is the same as pressing the ALL soft key when 
using the MEMORY folder method described in 

Restoring Option 

Module Parameters to Factory Defaults on page 3-9

.) After performing 

a Set Defaults, you must enter “1” (Reset Module) or power cycle the 

Parameter

Description

Host Parameter 37 - [Flt Cfg Logic]

A 32-bit value sent to the drive for Logic Command. 

Host Parameter 38 - [Flt Cfg Ref]

A 32-bit REAL (floating point) value sent to the drive for 
Reference.

Host Parameter 39 - [Flt Cfg DL 01]

through

Host Parameter 54 - [Flt Cfg DL 16]

A 32-bit REAL (floating point) or 32-bit integer value 
sent to the drive for a Datalink.

!

ATTENTION:  Risk of injury or equipment damage exists. If 
the Option Module is transmitting control I/O to the drive, the 
drive may fault when you reset the Option Module. 
Determine how your drive will respond before resetting the 
Option Module.

Value Description
0

Ready (Default)

1

Reset Module

2

Set Defaults

ESC

ENTER

Stopped
0.00 Hz

AUTO

F

▲

▼

Edit Reset Module

Ready

0

0 << 2

Содержание PowerFlex 750-Series

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды