Renesas Tsi301 HyperTransport Скачать руководство пользователя страница 77

Страница: 77 / 80

*Notice: The information in this document is subject to change without notice

Tsi301

Notes

Tsi301 HyperTransport to PCI User Manual

5-36

Note:

The value of this register is captured from the CRC logic following detection of a CRC error.

The value is unaffected by any form of reset. The value is undefined at power up.

HyperTransport PCI Bridge Diagnostics

Offset

D8h

Bits

Type

Reset

Description

7:5

Reserved.

Broadcast - broadcast enable bit for CSR read commands. If cleared to 0, Slave
ID (bits 3–0) is used. If set, read data is combined from all sources. Not persis-
tent through warm reset.

3:0

Slave ID - slave ID for CSR read commands. Used to specify a particular inter-
nal CSR slave module to read from. Not persistent through warm reset.

Diagnostics Link 0 Receive CRC Expected

Offset DFh–DCh

Bits

Type

Reset

Description

31:0

Expected CRC value for Link 0. This register is for software use and will survive
cold and warm reset as long as there is no power off.

Содержание Tsi301 HyperTransport

















































































Результаты поиска

Содержание Tsi301 HyperTransport

Отзывы:

Похожие инструкции для Tsi301 HyperTransport

Бренды по названию

Популярные бренды

Renesas Tsi301 HyperTransport, Руководство пользователя

Результаты поиска

Содержание Tsi301 HyperTransport

Отзывы:

Похожие инструкции для Tsi301 HyperTransport

Бренды по названию

Популярные бренды