Renesas Tsi301 HyperTransport Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 80

background image

*Notice: The information in this document is subject to change without notice

Tsi301

Notes

Tsi301 HyperTransport to PCI User Manual

5-36

Note:

In rev 1.0 of the Tsi301 HyperTransport to PCI bridge, the HyperTransport Revision ID is

given as 0.17. However, Pass1 is also compliant to LDT I/O Specification Revision 1.0, with the
exceptions that the Tsi301 does not support 2 and 4 bit interfaces or standard frequency control.

In Pass2, the HyperTransport Revision ID is 1.0. 2 and 4 bit interfaces are not supported.

Note:

In Pass1, the Link Frequency CSR did not exist.

4:0

R

Pass1 10001b
Pass2 00000b

Minor - minor revision ID of the HyperTransport specification supported by the
HyperTransport PCI bridge.

Link Frequency

Offset 4Dh

Bits

Type

Reset

Description

7:4

RW

0000b

Link 1 Frequency Control - controls the link transmitter frequency.

• If using sync mode, these bits also control the receiver

frequency.

• If the core133Sel and Lx_clkSel strappings are set to a

value logic can recognize as generating a 200 MHz

clock, the register reads 0000 at cold reset.

• If logic can not recognize the core133Sel and Lx-clkSel

strappings as generating a 200 MHz clock, the register

reads 1111 at cold reset.

• If SIP is used, the register reads 1111 at cold reset.

If the register comes up 0000 at cold reset, software can write it to either 0000
or 0010 and go through warm reset to switch between 200 and 400 MHz opera-
tion. All other encodings are reserved and can lead to undefined behavior.
Each 4-bit field contains one of the following values:
0000 = 200 MHz
0010 = 400 MHz
1111 = Vendor specified
Persistent through warm reset.

3:0

RW

0000b

Link 0 Frequency Control - controls the link transmitter frequency.

• If using sync mode, these bits also control the receiver

frequency.

• If the core133Sel and Lx_clkSel strappings are set to a

value logic can recognize as generating a 200 MHz

clock, the register reads 0000 at cold reset.

• If logic can not recognize the core133Sel and Lx-clkSel

strappings as generating a 200 MHz clock, the register

reads 1111 at cold reset.

• If SIP is used, the register reads 1111 at cold reset.

If the register comes up 0000 at cold reset, software can write it to either 0000
or 0010 and go through warm reset to switch between 200 and 400 MHz opera-
tion. All other encodings are reserved and can lead to undefined behavior.
Each 4-bit field contains one of the following values:
0000 = 200 MHz
0010 = 400 MHz
1111 = Vendor specified
Persistent through warm reset.

HyperTransport Revision ID

Offset 4Ch<Emphasis> (Continued)

Bits

Type

Reset

Description

«
...
61
62
63
64
65
...
»

Содержание Tsi301 HyperTransport

















































































Отзывы:

Нет отзывов

Похожие инструкции для Tsi301 HyperTransport

Бренд: SanDisk Страницы: 2

Pro AV 1600 PCI

Бренд: Focus Страницы: 24

Бренд: Klark Teknik Страницы: 36

Бренд: Elitegroup Computer Systems Страницы: 16

ViVOpay KioskII

Бренд: IDTECH Страницы: 19

DSerial-PCI/LP Card

Бренд: Lava Страницы: 8

Бренд: Roger Страницы: 54

Бренд: Virident Страницы: 33

Бренд: Sandberg Страницы: 12

Бренд: ADLINK Technology Страницы: 49

Бренд: Erma Electronic Страницы: 28

Бренд: SeaLevel Страницы: 21

Бренд: Ier Страницы: 17

Бренд: Digigram Страницы: 8

Бренд: Iron logic Страницы: 1

Бренд: Inventa Страницы: 16

Бренд: Wired Страницы: 44

Бренд: Digitus Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды