Renesas Tsi301 HyperTransport Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 80

background image

*Notice: The information in this document is subject to change without notice

Tsi301

Notes

Tsi301 HyperTransport to PCI User Manual

5-36

HyperTransport Rx Data Buffer Allocation

Offset 6Dh-6Ch

Bits

Type

Reset

Description

15:14

R

00b

Reserved.

13:12

RW

01b

WantPReq - the number of buffers minus one to try to keep released in the
posted request channel. Not persistent through warm reset.

11:10

RW

01b

WantNpReq - the number of buffers minus one to try to keep released in the
nonposted request channnel. Not persistent through warm reset.

9:8

RW

01b

WantResp - the number of buffers minus one to try to keep released in the
response channel. Not persistent through warm reset.

7:6

R

00b

Reserved.

5:4

RW

01b

NeedPReq - the mimimum data buffer allocation to the posted request channel.
Not persistent through warm reset.

3:2

RW

01b

NeedNpReq - the minimum data buffer allocation to the nonposted request
channel. Not persistent through warm reset.

0:1

RW

01b

NeedResp - the minimum data buffer allocation to the response channel. Not
persistent through warm reset.

HyperTransport Transmit Control

Offset 6Eh:6Eh

Bit

Type

Reset

Description

7:4

R

0h

Reserved

3:0

RW

4h

BufRelSpace - controls the throttling of buffer release messages on a busy bus.
If the bus is idle, buffer releases always get issued immediately. When the bus
is busy, buffer release messages are forced into the packet stream. This field
gives the minimum number of DW that must be allowed to pass between forced
buffer releases to prevent them from absorbing too much bandwidth. Not per-
sistent through warm reset.

PCI Control 2

Offset 6Fh–6Fh

Bit

Type

Reset

Description

7:4

R

0h

Reserved.

3:3

RW_R

1b

IntPassPW - value of the PassPW bit for interrupt packets. This bit controls
whether interrupts are allowed to pass other posted request packets. A value of
0 orders interrupts behind other posted writes (including other interrupts) from
this chip.

Note:

In Pass1, this CSR did not exist. Hardware behaved

as if this CSR was always set to 1.

«
...
66
67
68
69
70
...
»

Содержание Tsi301 HyperTransport

















































































Отзывы:

Нет отзывов

Похожие инструкции для Tsi301 HyperTransport

Бренд: FnL Страницы: 6

Бренд: Igloo Страницы: 7

Бренд: Q-See Страницы: 56

Бренд: DoorKing Страницы: 3

Бренд: Acorn computer Страницы: 182

e-mobility 802.11b Wireless LAN DSSS PCI Card

Бренд: Nortel Страницы: 18

Бренд: Gigabyte Страницы: 40

Бренд: MSI Страницы: 1

Бренд: Peak Страницы: 38

Бренд: Intratone Страницы: 2

Бренд: Intratone Страницы: 4

Video-PX7300GS-256

Бренд: Jaton Страницы: 26

Бренд: Intersil Страницы: 10

Бренд: Hamlet Страницы: 4

Бренд: Diablotek Страницы: 1

Бренд: EPOX Страницы: 20

Бренд: EPOX Страницы: 23

Бренд: IDTECK Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды