R&S SMA100A Скачать руководство пользователя страница 53

Страница: 53 / 176

AN680XX emulation mode

1GP71_0E

Rohde & Schwarz

Status

Command / Function / Remark / Limitation

SYSTem:LANGuage value

Select / Query the remote-control language.

Value:

“SCPI” | “NATIVE” | “TMSL” | “EXIT”

Remark:

“SCPI”, “NATIVE” and “TMSL” are not supported.

“EXIT” has to be used to return to the instruments native SCPI-language.

SYSTem:PRESet

Preset instrument.

Remark:

For more information, please see *RST command.

SYSTem:VERSion?

Query the SCPI software version.

Remark:

YYYY.V is returned.

Table 45: SYSTEM subsystem

•

TRIGger Subsystem

Status

Command / Function / Remark / Limitation

TRIGger[:SEQuence | :STARt][:IMMediate]

Trigger a sweep.

TRIGger[:SEQuence | :STARt]:SOURce value

Select / Query the trigger source.

Value:

BUS | EXTern | HOLD | IMMediate

Default:

BUS

Remark:

HOLD is not supported.

Table 46: TRIGGER subsystem

•

TSWeep Subsystem

Status

Command / Function / Remark / Limitation

TSWeep

Take a sweep.

Table 47: TSWEEP subsystem

•

UNIT Subsystem

Status

Command / Function / Remark / Limitation

Содержание SMA100A

















































































































































































Результаты поиска

Содержание SMA100A

Отзывы:

Похожие инструкции для SMA100A

Бренды по названию

Популярные бренды

R&S SMA100A, Приложения к руководству пользователя

Результаты поиска

Содержание SMA100A

Отзывы:

Похожие инструкции для SMA100A

Бренды по названию

Популярные бренды