R&S SMA100A Скачать руководство пользователя страница 100

Страница: 100 / 176

HP8373 emulation mode

1GP71_0E

100

Rohde & Schwarz

Status

Command / Function / Remark / Limitation

[SOURce[1]:]FREQuency[:CW | :FIXed]:STEP[:INCRement] value

Set / Query the rf carrier frequency step size.

Value:

Fmin … FMax [HZ | KHZ | MHZ | MHZ | GHZ] | MINimum | MAXimum | DEFault

Default:

Remark:

MINimum, MAXimum, DEFault are not supported.

[SOURce[1]:]FREQuency:MULTiplier value

Value:

Default:

1.0

Remark:

UP, DOWN, MINimum, MAXimum, DEFault are not supported.

[SOURce[1]:]FREQuency:MULTiplier:STEP[:INCRement] value

Table 93: Carrier commands

•

Instrument information

Status

Command / Function / Remark / Limitation

OUTPut:IMPedance? value

[SOURce[1]:]ROSCillator:SOURce?

Query the source of the synthesizer toimebase reference

SYSTem:ERRor?

Query and clear the oldest error number and error description

Remark:

Returns in error in the SM* naming convention

SYSTem:VERSion?

Query the SCPI version number that the instruments supports.

Table 94: Instrument information commands

•

Instrument state

Status

Command / Function / Remark / Limitation

MEMory:RAM:INITialize[:ALL]

SYSTem:PRESet

Table 95: Instrument information commands

•

Level correction

Status

Command / Function / Remark / Limitation

Содержание SMA100A

















































































































































































Результаты поиска

Содержание SMA100A

Отзывы:

Похожие инструкции для SMA100A

Бренды по названию

Популярные бренды

R&S SMA100A, Приложения к руководству пользователя

Результаты поиска

Содержание SMA100A

Отзывы:

Похожие инструкции для SMA100A

Бренды по названию

Популярные бренды