RAM CHASSIS CAB 2024, Руководство пользователя

Страница: 100 / 360

If the vehicle is not in PARK and the driver exits the vehicle
with the engine running, the vehicle may AutoPark.
AutoPark will engage when all of these conditions are met:
•
Vehicle is equipped with a rotary shifter and an
8-speed transmission
•
Vehicle is not in PARK
•
Vehicle speed is 1.2 mph (1.9 km/h) or less
•
Driver’s seat belt is unbuckled
•
Driver’s door is ajar
•
Brake pedal is not pressed
The message “
AutoPark Engaged Shift To P Then Shift
To Gear
” will display in the instrument cluster.
NOTE:
In some cases the ParkSense graphic will be displayed
in the instrument cluster, causing the “
AutoPark
Engaged Shift To P Then Shift To Gear
” to not be seen.
In these cases, the shifter must be returned to “P” to
select desired gear.
If the driver shifts into PARK while moving, the vehicle
may AutoPark.
AutoPark will engage
ONLY
when vehicle speed is
1.2 mph (1.9 km/h) or less.
The message “
Vehicle Speed Is Too High To Shift To P
”
will be displayed in the instrument cluster if vehicle
speed is above 1.2 mph (1.9 km/h).
WARNING!
If vehicle speed is above 1.2 mph (1.9 km/h), the trans-
mission will default to NEUTRAL until the vehicle speed
drops below 1.2 mph (1.9 km/h). A vehicle left in the
NEUTRAL position can roll. As an added precaution,
always apply the parking brake when exiting the vehicle.
4WD Low — If Equipped
AutoPark will be disabled when operating the vehicle
in 4WD LOW.
The message “
AutoPark Disabled
” will be displayed in
the instrument cluster.
Additional customer warnings will be given when all of
these conditions are met:
•
Vehicle is not in PARK
•
Driver’s door is ajar
•
Vehicle is in 4WD Low range
The message “
AutoPark Not Engaged
” will be dis-
played in the instrument cluster. A warning chime will
continue until you shift the vehicle into PARK or the
driver’s door is closed.
ALWAYS DO A VISUAL CHECK
that your vehicle is in
PARK by looking for the “P” in the instrument cluster
display and near the shifter. As an added precaution,
always apply the parking brake when exiting the
vehicle.
TIP START FEATURE
Do not
press the accelerator. Place the ignition switch
briefly to the START position and release it. The starter
motor will continue to run and will automatically disen-
gage when the engine is running.
KEYLESS ENTER ‘N GO™ —
IGNITION
This feature allows the driver to operate the ignition
switch with the push of a button, as long as the Remote
Start/Keyless Enter ‘n Go™ key fob is in the passenger
compartment.
NORMAL STARTING USING ENGINE
START/STOP BUTTON
To Turn On The Engine Using The ENGINE START/STOP
Button
1. The transmission must be in PARK.
2. Press and hold the brake pedal while pushing the
ENGINE START/STOP button once.
3. The system takes over and attempts to start the
vehicle. If the vehicle fails to start, the starter will
disengage automatically after 10 seconds.
4. If you wish to stop the cranking of the engine prior to
the engine starting, push the ENGINE START/STOP
button again.
NOTE:
Normal starting of either a cold or a warm engine is
obtained without pumping or pressing the accelerator
pedal.
To Turn Off The Engine Using ENGINE START/STOP
Button
1. Place the gear selector in PARK, then push and
release the ENGINE START/STOP button.
2. The ignition will return to the OFF position.
3. If the gear selector is not in PARK, the ENGINE
START/STOP button must be held for two seconds or
three short pushes in a row with the vehicle speed
above 5 mph (8 km/h) before the engine will shut
off. The ignition will remain in the ACC position until
the gear selector is in PARK and the button is
pushed twice to the OFF position.
98 STARTING AND OPERATING