RAM CHASSIS CAB 2024, Руководство пользователя

Страница: 261 / 360

8. If the child restraint has a top tether strap and the
seating position has a top tether anchorage, con-
nect the tether strap to the anchorage and tighten
the tether strap. See
page 259 for directions to
attach a tether anchor.
9. Test that the child restraint is installed tightly by
pulling back and forth on the child seat at the belt
path. It should not move more than 1 inch
(25.4 mm) in any direction.
Any seat belt system will loosen with time, so check the
belt occasionally, and pull it tight if necessary.
Installing A Child Restraint With A
Cinching Latch Plate (CINCH) —
If Equipped:
Child restraint systems are designed to be secured in
vehicle seats by lap belts or the lap belt portion of a
lap/shoulder belt.
WARNING!
•
Improper installation or failure to properly secure a
child restraint can lead to failure of the restraint.
The child could be badly injured or killed.
•
Follow the child restraint manufacturer’s directions
exactly when installing an infant or child restraint.
1. Place the child seat in the center of the seating posi-
tion. If the second row seat can be reclined, you may
recline the seat and/or raise the head restraint (if
adjustable) to get a better fit. If the rear seat can be
moved forward and rearward in the vehicle, you may
wish to move it to its rear-most position to make
room for the child seat. You may also move the front
seat forward to allow more room for the child seat.
2. Next, pull enough of the seat belt webbing from the
retractor to pass it through the belt path of the child
restraint. Do not twist the belt webbing in the belt path.
3. Slide the latch plate into the buckle until you hear a
“click.”
4. Finally, pull up on any excess webbing to tighten the
lap portion around the child restraint while you push
the child restraint rearward and downward into the
vehicle seat.
5. If the child restraint has a top tether strap and the
seating position has a top tether anchorage, con-
nect the tether strap to the anchorage and tighten
the tether strap. See
page 259 for directions to
attach a tether anchor.
6. Test that the child restraint is installed tightly by
pulling back and forth on the child seat at the belt
path. It should not move more than 1 inch
(25.4 mm) in any direction.
Any seat belt system will loosen with time, so check the
belt occasionally, and pull it tight if necessary.
If the buckle or the cinching latch plate is too close to
the belt path opening of the child restraint, you may
have trouble tightening the seat belt. If this happens,
disconnect the latch plate from the buckle and twist the
short buckle-end belt up to three full turns to shorten it.
Insert the latch plate into the buckle with the release
button facing out, away from the child restraint. Repeat
steps 4 to 6, above, to complete the installation of the
child restraint.
If the belt still cannot be tightened after you shorten the
buckle, disconnect the latch plate from the buckle, turn
the buckle around one half turn, and insert the latch
plate into the buckle again. If you still cannot make the
child restraint installation tight, try a different seating
position.
Installing Child Restraints Using The Top
Tether Anchorage
WARNING!
Do not attach a tether strap for a rear-facing car seat
to any location in front of the car seat, including the
seat frame or a tether anchorage. Only attach the
tether strap of a rear-facing car seat to the tether
anchorage that is approved for that seating position,
located behind the top of the vehicle seat. For the
location of approved tether anchorages in your
vehicle, see
page 253.
Regular Cab Trucks:
In the regular cab truck, the top tether
anchorages are located behind the center
and right passenger seats. There is a plastic
cover over each anchorage. To attach the
tether strap of the child restraint:
1. Place the child restraint on the seat and adjust the
tether strap so that it will reach over the seat back,
under the head restraint and to the tether anchor
directly behind the seat.
SAFETY 259
6